Skip to content

How-ToMotherboard

How to Clear CMOS and Reset Your BIOS to Default Settings

Clearing CMOS resets your BIOS settings, date and time to default and often fixes a PC that won't boot after an overclock or memory profile change. Use the Clear CMOS button, short the CLRTC pins for 5 to 10 seconds, or remove the CMOS battery with the power cord unplugged, then load defaults.

By , Editorial team

4 min read

How to Clear CMOS and Reset Your BIOS to Default Settings

If your PC stopped booting after you changed a BIOS setting, enabled a memory profile or tried an overclock, clearing the CMOS is one of the first things to try. It resets the motherboard's firmware settings to their defaults, which often brings an unstable system back to life.

Forge PC hasn't tested every motherboard. The steps below follow ASUS's official "How to Clear CMOS" support guide; other brands use the same three methods, but connector names and positions differ, so always check your motherboard manual.

What clearing CMOS does

ASUS explains that clearing CMOS clears the real-time clock (RTC) memory, which holds the date, time, BIOS password and BIOS setup parameters. That means:

  • Every BIOS setting returns to default, including memory profiles (XMP or EXPO), fan curves, boot order and any overclock.

  • The date and time will need setting again.

  • Your files, Windows installation and drivers are not affected.

ASUS gives an unstable system, crashes or freezes after overclocking as typical reasons to clear CMOS.

Before you start

  • Try the BIOS first if you can. If the PC still reaches the BIOS, simply loading defaults is quicker. ASUS's guide uses F5 for Load Optimized Defaults and F10 to save and exit. Other brands have a similar "Load defaults" option.

  • Note your settings. Take photos of BIOS pages you've changed, such as memory and fan settings, so you can put them back.

  • Power off fully. Shut down, switch off at the wall and remove the power cord, as ASUS instructs for every method.

Method 1: the Clear CMOS button

Some motherboards have a button labelled Clear CMOS or CLR_CMOS, often on the rear I/O panel.

  1. Power off the PC and remove the power cord.

  2. Press and hold the Clear CMOS button for about 5 to 10 seconds, as ASUS recommends.

  3. Plug the power cord back in and turn the PC on.

  4. The BIOS will show a message that settings have been reset. On ASUS boards, press F1 to enter the BIOS, F5 to load optimised defaults, then F10 to save and exit.

Method 2: the CLRTC jumper pins

If there's no button, look for a two-pin header labelled CLRTC, CLR_CMOS or similar on the motherboard (your manual shows where).

  1. Power off the PC and remove the power cord.

  2. Open the case and find the two pins.

  3. Short the two pins with a jumper cap or a metal object, such as a screwdriver tip, for about 5 to 10 seconds, following ASUS's guide.

  4. Remove the jumper or tool, plug in the power cord and turn the PC on, then load defaults as above.

Method 3: remove the CMOS battery

ASUS lists removing the battery as the third method. Most boards use a coin-cell battery in a holder.

  1. Power off the PC and remove the power cord.

  2. Open the case and find the CMOS battery holder. It may be partly hidden under the graphics card, so you may need to remove the card first.

  3. Release the battery using the tab on its holder and take it out.

  4. Put the battery back in, plug the power cord in and turn the PC on.

Some boards use a battery on a two-pin cable instead of a holder. For those, ASUS says to unplug the battery cable from the motherboard, clear CMOS using the CLRTC pins or Clear CMOS button as above, then reconnect the cable before plugging in the power cord and turning the PC on.

After clearing CMOS

  1. Enter the BIOS, set the date and time, and check the boot drive is first in the boot order.

  2. If you use a modern CPU on Windows 11, check that settings such as TPM and Secure Boot are as you need them; see our guide to enabling Secure Boot and TPM.

  3. Re-enable your memory profile carefully. If the problem started after turning on XMP or EXPO, try it again; if the PC fails again, try the profile's lower speed or leave it off and check the motherboard's memory support list. Our XMP and EXPO guide explains the options.

If it still won't boot

Clearing CMOS fixes settings problems, not hardware faults. If your PC still won't start, work through our PC won't turn on or boot guide and our no display, no signal fixes. If the problems began after a BIOS update, see how to update your BIOS safely.

Our verdict

Clearing CMOS resets your BIOS to its defaults and is the quickest fix for a PC that stopped booting after a settings change. If you can still reach the BIOS, load optimised defaults there. Otherwise, with the power cord removed, press the Clear CMOS button or short the CLRTC pins for 5 to 10 seconds, or remove the CMOS battery, as ASUS describes. Then reset the date and boot order and re-enable memory profiles one at a time. Forge PC hasn't tested every board, so check your manual for connector locations.

The bottom line

Clearing CMOS resets your BIOS to its defaults and is the quickest fix for a PC that stopped booting after a settings change. If you can still reach the BIOS, load optimised defaults there. Otherwise, with the power cord removed, press the Clear CMOS button or short the CLRTC pins for 5 to 10 seconds, or remove the CMOS battery, as ASUS describes. Then reset the date and boot order and re-enable memory profiles one at a time. Forge PC hasn't tested every board, so check your manual for connector locations.

Sources

  1. 01ASUS, [Motherboard] How to Clear CMOS

About the author

Forge PC Staff

Editorial team

The shared byline for articles researched, written and edited by the Forge PC editorial team. How we source, check and correct our work is set out in our editorial policy.

More from Forge PC Staff

Read next

Two vs Four RAM Sticks for DDR5: Why 2x32GB Usually Beats 4x16GB

Versus

Two vs Four RAM Sticks for DDR5: Why 2x32GB Usually Beats 4x16GB

Two DDR5 sticks are better for most builds. AMD lists DDR5-5600 as the AM5 maximum with two modules but DDR5-3600 with four, and XMP or EXPO speeds above that are overclocking and not guaranteed. Buy 2x16GB or 2x32GB for 32GB or 64GB, and use four sticks, ideally a matched kit, only if you need 128GB or more.

Forge PC Staff3 min

Best Wi-Fi 7 PCIe Card for Desktop PCs in 2026

Best Picks

Best Wi-Fi 7 PCIe Card for Desktop PCs in 2026

The TP-Link Archer TBE550E is the best Wi-Fi 7 PCIe card for most desktops: it works on AMD systems, supports 320MHz and MLO and was about £85 at Scan (17 Nov 2026), but it's Windows 11 only. The ASUS PCE-BE92BT (about £51) suits recent Intel PCs only. The ASUS PCE-BE6500 (about £34) is the budget pick.

Forge PC Staff4 min

ARGB vs RGB: 5V 3-Pin and 12V 4-Pin Headers Explained (and How Not to Fry Them)

Versus

ARGB vs RGB: 5V 3-Pin and 12V 4-Pin Headers Explained (and How Not to Fry Them)

5V ARGB uses a 3-pin header and controls each LED individually for animations and gradients; 12V RGB uses a 4-pin header and shows one colour at a time. They aren't interchangeable, and plugging either into the wrong header can permanently damage the lighting, the motherboard or both. Check the pin count and the board label, and use a controller if needed.

Forge PC Staff4 min

How to Install a CPU: AM5, LGA 1851 and AM4 Step by Step

How-To

How to Install a CPU: AM5, LGA 1851 and AM4 Step by Step

To install a CPU, unplug the PC and avoid static, release the socket lever and lift the load plate, match the triangle on the processor to the one on the socket, lower it straight in without force, then close the plate and lock the lever. On AM5 and Intel boards the plastic cover pops off; keep it. Check CPU support and update the BIOS first if needed.

Forge PC Staff4 min