Skip to content

How-ToCase

How to Cable Manage a PC: A Step-by-Step Guide for Tidy Builds

A step-by-step guide to PC cable management: plan routes, connect CPU power and front panel cables first, use the nearest cut-out for each connector, tidy the back of the case and avoid common mistakes such as mixing modular PSU cables. Includes tips from Corsair's 3500X guide.

By , Editorial team

4 min read

How to Cable Manage a PC: A Step-by-Step Guide for Tidy Builds

Cable management is the difference between a PC that looks like a bird's nest and one you're happy to show off through a glass side panel. It also makes upgrades and cleaning easier and keeps cables away from fans. You don't need special tools, just some planning, a handful of cable ties and patience.

Forge PC hasn't tested every case and part mentioned here. Case and power supply details come from manufacturers' official pages, including Corsair's cable management guide for its 3500X case.

What you need

  • Cable ties or Velcro straps. Many cases include them; Phanteks, for example, includes 30 zip ties with its XT Pro case. Reusable Velcro straps make later changes easier.

  • Side cutters or small scissors for trimming zip ties. Cut them flush and carefully so you don't nick a cable.

  • A torch to see behind the motherboard tray.

Step 1: Plan before you build

Before you install anything, look at your case and work out where each cable will go:

  • Cable cut-outs and grommets: the holes beside and above the motherboard where cables pass through.

  • Tie-down points: loops on the back of the motherboard tray to anchor cables.

  • Space behind the tray: more space makes it easier to close the side panel.

If you're still choosing parts, two features make cable management easier:

  • A modular power supply lets you connect only the cables you need. See our modular vs non-modular PSU comparison.

  • A back-connect motherboard puts power and data connectors on the back of the board. Corsair's 3500X guide says the case works with ASUS BTF and MSI Project Zero boards, so the 24-pin and graphics card power cables plug in from behind. Our back-connect vs standard motherboard guide explains the trade-offs.

Step 2: Connect the hard-to-reach cables first

Some connectors are very hard to reach once the motherboard, cooler and graphics card are in place:

  1. CPU power (8-pin EPS). Route it through the top-left cut-out before installing a large cooler or top radiator. Corsair's 3500X guide runs the EPS cable along the back corner of the case to keep it hidden.

  2. Front panel connectors for the power button, USB and audio. Our front panel connector guide shows where they go.

  3. Fan and RGB headers near the top and bottom edges of the board.

Step 3: Route cables through the nearest cut-out

Use the cut-out closest to each connector so cables travel the shortest visible distance:

  • 24-pin motherboard power: through the cut-out next to the connector on the right edge of the board.

  • Graphics card power: through the cut-out in the PSU shroud below the card. If your card uses a 12V-2x6 connector, make sure it's fully inserted and avoid bending it sharply near the plug. Our 12V-2x6 guide covers this in detail.

  • SATA and front panel cables: along the bottom edge.

Corsair's guide also suggests tucking front I/O cables such as USB and audio behind the drive tray before routing them to their headers.

Step 4: Tidy the back of the case

  1. Group cables that run the same way and tie them together loosely.

  2. Anchor bundles to the tie-down points on the motherboard tray.

  3. Push spare cable length into the power supply area under the shroud.

  4. Keep cables flat so the side panel closes without pressing on them.

A power supply with connectors on the side, like Corsair's RMx SHIFT used in its 3500X guide, can make this easier. Some cases do something similar: Lian Li's LANCOOL 207 mounts the power supply at the front with side-facing connector ports, which Lian Li says makes cable management easier.

Step 5: Check airflow and close up

Before you close the case:

  • Make sure no cables touch fan blades, including CPU cooler and graphics card fans.

  • Keep cables out of the path of front intake fans. Our case fan airflow guide shows how air should move through the case.

  • Turn the PC on with the side panels off to check everything works before tidying the last few cables.

Common mistakes to avoid

  • Pulling ties too tight. It can damage cables and makes changes harder.

  • Bending cables sharply at connectors, especially graphics card power cables.

  • Mixing PSU cables from different brands or models. Modular cables aren't standardised, so only use the cables that came with your power supply.

  • Forgetting future upgrades. Leave a little slack so you can add a drive or swap a graphics card without redoing everything.

If you're building from scratch, our how to build a gaming PC guide covers the full process.

Our verdict

Good cable management comes down to planning: connect the CPU power and front panel cables early, use the nearest cut-out for each connector, bundle cables on the back of the case and push spare length under the PSU shroud. A modular power supply and a case with plenty of space and tie-down points make the job much easier, and back-connect motherboards and side-connector PSUs can make it easier still. Above all, never mix modular cables between power supplies and never bend graphics card power cables sharply.

The bottom line

Good cable management comes down to planning: connect the CPU power and front panel cables early, use the nearest cut-out for each connector, bundle cables on the back of the case and push spare length under the PSU shroud. A modular power supply and a case with plenty of space and tie-down points make the job much easier, and back-connect motherboards and side-connector PSUs can make it easier still. Above all, never mix modular cables between power supplies and never bend graphics card power cables sharply.

In this article

Sources

  1. 01Corsair, Cable management guide for CORSAIR 3500X
  2. 02Lian Li, LANCOOL 207
  3. 03Phanteks, XT Pro specifications

About the author

Forge PC Staff

Editorial team

The shared byline for articles researched, written and edited by the Forge PC editorial team. How we source, check and correct our work is set out in our editorial policy.

More from Forge PC Staff

Read next

Two vs Four RAM Sticks for DDR5: Why 2x32GB Usually Beats 4x16GB

Versus

Two vs Four RAM Sticks for DDR5: Why 2x32GB Usually Beats 4x16GB

Two DDR5 sticks are better for most builds. AMD lists DDR5-5600 as the AM5 maximum with two modules but DDR5-3600 with four, and XMP or EXPO speeds above that are overclocking and not guaranteed. Buy 2x16GB or 2x32GB for 32GB or 64GB, and use four sticks, ideally a matched kit, only if you need 128GB or more.

Forge PC Staff3 min

Best Wi-Fi 7 PCIe Card for Desktop PCs in 2026

Best Picks

Best Wi-Fi 7 PCIe Card for Desktop PCs in 2026

The TP-Link Archer TBE550E is the best Wi-Fi 7 PCIe card for most desktops: it works on AMD systems, supports 320MHz and MLO and was about £85 at Scan (17 Nov 2026), but it's Windows 11 only. The ASUS PCE-BE92BT (about £51) suits recent Intel PCs only. The ASUS PCE-BE6500 (about £34) is the budget pick.

Forge PC Staff4 min

SFX vs SFX-L vs ATX Power Supply: Which PSU Size Do You Need?

Versus

SFX vs SFX-L vs ATX Power Supply: Which PSU Size Do You Need?

ATX power supplies are 150 x 86mm with a depth of 140mm or more; SFX units are 125 x 63.5 x 100mm and SFX-L units are 125 x 63.5 x 130mm. Buy ATX for normal towers, SFX for compact mini-ITX cases and SFX-L only if your case supports it. An SFX unit can fit an ATX case with a bracket, but an ATX unit won't fit an SFX-only case.

Forge PC Staff4 min

ARGB vs RGB: 5V 3-Pin and 12V 4-Pin Headers Explained (and How Not to Fry Them)

Versus

ARGB vs RGB: 5V 3-Pin and 12V 4-Pin Headers Explained (and How Not to Fry Them)

5V ARGB uses a 3-pin header and controls each LED individually for animations and gradients; 12V RGB uses a 4-pin header and shows one colour at a time. They aren't interchangeable, and plugging either into the wrong header can permanently damage the lighting, the motherboard or both. Check the pin count and the board label, and use a controller if needed.

Forge PC Staff4 min