A new CPU in an older motherboard, a failed update or a board that powers on but shows nothing: these are the situations where a USB BIOS flashback feature earns its keep. Many recent motherboards have a dedicated button and USB port on the rear I/O that can write a BIOS file from a USB stick without going through the normal BIOS menu. ASUS calls this USB BIOS FlashBack, and MSI calls it the Flash BIOS Button.
This guide follows ASUS's and MSI's official instructions. Forge PC hasn't tested every board, and the exact port, button and LED positions vary by model. Always check your motherboard manual first. If your board boots normally, the standard in-BIOS updater is usually simpler. See our guide to updating your BIOS safely.
Before you start
Check that your board has the feature. MSI says the Flash BIOS Button is only on models that have the physical button. ASUS has a support page listing which boards support FlashBack. Look for a labelled button and a USB port marked "BIOS" or "FlashBack" on the rear I/O.
Find your exact model. You need the BIOS for your exact board and revision. Our guide to checking your motherboard model can help if the PC still boots.
Use a spare USB stick. Both makers require FAT32 formatting, and formatting erases the drive. ASUS asks for a drive of 1GB or more, formatted as FAT16 or FAT32 with an MBR partition table.
ASUS: USB BIOS FlashBack
Download the latest BIOS for your exact model from the ASUS Download Center (Driver and Utility > BIOS and FIRMWARE).
Extract the download. It contains the BIOS file (.CAP) and a BIOSRenamer tool.
Run BIOSRenamer to rename the .CAP file automatically.
Copy the renamed .CAP file to the root of the FAT32 USB drive.
Plug the drive into the FlashBack USB port shown in your manual.
Shut the PC down, but leave the power supply switched on and connected.
Hold the FlashBack button for about three seconds until the FlashBack LED blinks three times, then let go.
Wait until the light goes out. That means the update is complete.
ASUS says the update can take up to about eight minutes, depending on the BIOS file size. While it runs, don't remove the USB drive, unplug the power, turn on the PC or press Clear CMOS. ASUS warns that interrupting it will stop the system booting.
MSI says the Flash BIOS Button can refresh the BIOS without a CPU or RAM installed.
Format a USB drive as FAT32.
Download the latest BIOS for your exact model from MSI's website and extract it.
Rename the extracted BIOS file to MSI.ROM and copy it to the USB drive.
Connect the CPU power cable to CPU_PWR1 and the 24-pin ATX power cable to the motherboard.
Plug the USB drive into the rear USB port labelled BIOS.
Press the Flash BIOS Button. The indicator light will flash rapidly.
When the light goes off, the BIOS refresh has finished.
MSI warns not to power off during the process, as this may damage the BIOS chip.
If it doesn't work
The light doesn't flash, or stops straight away: check the file name (MSI.ROM for MSI, or the BIOSRenamer output for ASUS), make sure the file is in the root of the drive, and confirm the drive is FAT32. Then try a different, smaller USB stick.
Wrong port: the feature only works from the specific labelled USB port.
Still no display afterwards: clear the CMOS (how to clear CMOS), then work through our no display troubleshooting guide. If your board has debug LEDs, our guide to reading motherboard debug LEDs will help narrow it down.
Other motherboard makers have similar features under their own names. Check your manual for the exact steps, because file names and ports differ.
Our verdict
BIOS FlashBack (ASUS) and the Flash BIOS Button (MSI) let you update a BIOS from a FAT32 USB stick when the board won't boot or doesn't yet support your CPU. On ASUS boards, rename the file with BIOSRenamer, hold the button for three seconds and wait for the light to go out. On MSI boards, rename the file MSI.ROM, connect CPU and 24-pin power, use the port labelled BIOS and wait for the light to go off. Never cut power mid-flash.