Skip to content

How-ToMotherboard

Windows Shows Less Usable RAM Than Installed? How to Find the Cause and Fix It

A small gap between installed and usable RAM is normal hardware reservation. A big gap usually comes from integrated graphics reserving memory, a Maximum memory limit set in msconfig, or the removememory and truncatememory boot options. If installed RAM itself is too low, reseat the sticks, check the slots and BIOS, then test each stick.

By , Editorial team

4 min read

Windows Shows Less Usable RAM Than Installed? How to Find the Cause and Fix It

Open Settings > System > About and Windows shows two memory figures: installed RAM and usable RAM. A small gap between them is normal. A big gap, such as 32GB installed but only 16GB usable, or Windows reporting less memory than you fitted, means something needs fixing. This guide walks through the causes from most to least likely. It's based on Microsoft's documentation. Forge PC hasn't tested every motherboard, and BIOS menu names vary between manufacturers, so check your board's manual for exact wording.

First, work out which problem you have

There are two different situations, and they have different fixes:

  1. Installed RAM is correct, but usable RAM is lower. Windows can see all the memory, but some of it is reserved or blocked. Go to the "reserved memory" checks below.

  2. Installed RAM itself is too low. For example, you fitted 2x16GB and Windows shows 16GB installed. The system can't see a stick or a slot, so skip to "When a stick isn't detected".

To see where the gap comes from, open Task Manager > Performance > Memory. The "Hardware reserved" figure shows how much memory is set aside before Windows can use it. Our guide to checking your PC's specs also shows how to see the speed and number of sticks.

Cause 1: Integrated graphics reserving memory

If your monitor is plugged into the motherboard rather than a graphics card, or your CPU's integrated graphics are enabled, some RAM may be set aside for the GPU. Microsoft's DirectX team explains that some integrated GPUs reserve memory in firmware or during driver start-up from main system RAM. That memory is "taken away from Windows" and appears as hardware reserved.

This is different from shared GPU memory, which Task Manager also shows. Microsoft says shared memory is normal system memory that either the CPU or the GPU can use as needed, and Windows only lets the GPU use up to half of physical memory at any one time. Shared memory isn't removed from your usable total.

Fix: if you have a graphics card, plug your monitor into it. Then look in the BIOS for the integrated graphics memory (frame buffer) setting and reduce it or turn off the integrated GPU. The option is usually in an advanced chipset or graphics section of the BIOS. If you rely on integrated graphics, a modest reservation is expected. See how to check VRAM usage in Windows for more on dedicated and shared memory.

Cause 2: A boot setting is limiting memory

Windows has boot options that deliberately cap memory. Microsoft's BCDEdit documentation lists two:

  • removememory removes a set number of megabytes from the memory Windows can use.

  • truncatememory makes Windows ignore all memory at or above a given physical address.

These are mainly for testing, but they're sometimes left on by mistake. The Maximum memory box in System Configuration (msconfig) sets the same kind of limit: answers on Microsoft Q&A about resetting it show that the fix is to delete the truncatememory and removememory boot values.

Fix:

  1. Press Win+R, type msconfig and press Enter.

  2. Open the Boot tab and click Advanced options.

  3. Untick Maximum memory, click OK and restart.

Advanced users can check for removememory or truncatememory entries by running bcdedit /enum in an administrator terminal. Only remove settings you understand, because a broken boot configuration can stop Windows starting.

Cause 3: Your version of Windows has a limit

Microsoft's memory limits page lists the maximum physical memory for each edition. Windows 11 Home supports up to 128GB and Windows 11 Pro up to 2TB, so most home PCs will never hit a limit. Older 32-bit versions of Windows 10 are capped at 4GB. If you're still running a 32-bit Windows 10 install, extra RAM won't help until you reinstall a 64-bit version. Windows 11 is only available for x64 and ARM64. For the differences between editions, see Windows 11 Home vs Pro.

When a stick isn't detected

If the installed figure is too low, the PC isn't seeing all the hardware:

  1. Reseat the modules. Switch off, unplug the PC, press the power button to drain it, then remove each stick and push it back in firmly until the latches click. Partly seated DDR5 sticks are a common cause. Our guide to installing RAM shows the technique.

  2. Use the right slots. With two sticks on a four-slot board, most manuals specify the second and fourth slots (often labelled A2 and B2). Check your manual.

  3. Check the BIOS. If the BIOS also shows less memory, the problem is hardware or firmware, not Windows. Updating the BIOS can add support for newer, higher-capacity modules. See how to update your BIOS safely. If the board won't boot properly after a memory change, clearing CMOS resets the memory settings.

  4. Test one stick at a time. Boot with each module on its own in the recommended slot. If one stick or slot never shows up, you've found the fault.

  5. Run a memory test. Once all the memory is detected, check it's stable with MemTest86.

Mixing different kits can also cause detection and stability problems, so if you added sticks to an existing set, test the original kit on its own.

Our verdict

A small gap between installed and usable RAM is normal hardware reservation. A large gap usually comes from integrated graphics reserving memory, or a Maximum memory limit set in msconfig, or the removememory and truncatememory boot options. If Windows shows less installed RAM than you fitted, reseat the sticks, check you're using the right slots, check the BIOS, then test each stick on its own and run MemTest86.

The bottom line

A small gap between installed and usable RAM is normal hardware reservation. A large gap usually comes from integrated graphics reserving memory, or a Maximum memory limit set in msconfig, or the removememory and truncatememory boot options. If Windows shows less installed RAM than you fitted, reseat the sticks, check you're using the right slots, check the BIOS, then test each stick on its own and run MemTest86.

Sources

  1. 01Microsoft DirectX Developer Blog, GPUs in the Task Manager
  2. 02Microsoft Learn, BCDEdit /set
  3. 03Microsoft Learn, Memory Limits for Windows and Windows Server Releases
  4. 04Microsoft Q&A, How to reset msconfig > Boot > Advanced Options > Maximum Memory

About the author

Forge PC Staff

Editorial team

The shared byline for articles researched, written and edited by the Forge PC editorial team. How we source, check and correct our work is set out in our editorial policy.

More from Forge PC Staff

Read next

How to Turn Off Mouse Acceleration in Windows 11 (Enhance Pointer Precision)

How-To

How to Turn Off Mouse Acceleration in Windows 11 (Enhance Pointer Precision)

To turn off mouse acceleration in Windows 11, go to Settings > Bluetooth & devices > Mouse and switch off Enhance pointer precision (or untick it under Additional mouse settings > Pointer Options). Then set your DPI or pointer speed, and check your mouse software for any extra acceleration setting.

Forge PC Staff3 min

How to Dual Boot Windows 11 and Linux (Ubuntu) Without Losing Your Files

How-To

How to Dual Boot Windows 11 and Linux (Ubuntu) Without Losing Your Files

To dual boot Windows 11 and Ubuntu, back up first. Installing Ubuntu on its own SSD is the safest option and avoids turning off BitLocker. On a single drive, turn BitLocker off and shrink C: in Disk Management. Then create a USB installer with balenaEtcher and choose 'Install Ubuntu alongside Windows'. Ubuntu needs at least 25GB.

Forge PC Staff4 min

How to Use Microsoft's AI Dev Gallery to Try Local AI Models on Your PC

How-To

How to Use Microsoft's AI Dev Gallery to Try Local AI Models on Your PC

AI Dev Gallery is Microsoft's free, open-source Windows app with more than 25 local AI samples that can run on your CPU, GPU or NPU. Install it from the Microsoft Store, pick a sample, read the model card and download the model. After that it works offline. Microsoft recommends 16GB RAM, 20GB free space and 8GB VRAM for GPU samples.

Forge PC Staff4 min

How to Use ControlNet in ComfyUI: Guide Your AI Images With Sketches, Depth and Poses

How-To

How to Use ControlNet in ComfyUI: Guide Your AI Images With Sketches, Depth and Poses

ControlNet lets a local image model follow a sketch, edge map, depth map or pose. Put a ControlNet model that matches your base model in ComfyUI/models/controlnet, install ComfyUI ControlNet aux through ComfyUI Manager for preprocessors, add Load ControlNet and Apply ControlNet before the KSampler, then tune strength, start and end.

Forge PC Staff4 min