Skip to content

How-ToNetworking

How to Fix High Ping and Packet Loss on a Gaming PC

Fix lag by finding where it starts: test on Ethernet, ping your router and then an internet site with -n 100, and run pathping to see the hop where packet loss begins. Loss inside your home points to Wi-Fi, cables, the router or drivers, which Microsoft's reset commands can help with; loss beyond your router is for your provider, and pathping results give you the evidence. Forge PC has not tested

By , Editorial team

5 min read

How to Fix High Ping and Packet Loss on a Gaming PC

Few things ruin an online game faster than lag. Rubber-banding, delayed shots and sudden disconnects are usually caused by one of two things: high ping (latency, the time it takes data to reach the server and back) or packet loss (data that never arrives). The good news is that Windows includes tools that can tell you where the problem is, so you can fix the right thing instead of guessing.

Forge PC has not tested specific networks or routers for this guide. The commands and how to read their output are based on Microsoft's documentation for ping, tracert and pathping, and its Windows network troubleshooting guide, checked on 16 November 2026.

Ping vs packet loss

  • High but steady ping makes everything feel slightly delayed. It's often caused by distance to the server, Wi-Fi, or a busy connection.

  • Jitter (ping that jumps around) causes stutter and rubber-banding.

  • Packet loss causes teleporting players, missed hits and disconnects. Even a few per cent is noticeable in fast games.

If games also stutter when you're playing offline, the problem is probably your PC rather than your network: see our game stuttering guide and input lag guide.

Step 1: Rule out Wi-Fi

If you can, plug your PC into the router with an Ethernet cable and play for a while. If the lag disappears, the problem is your wireless connection: interference, distance or walls. Our Wi-Fi vs Ethernet vs powerline comparison explains the options if running a cable isn't practical, and our Wi-Fi 7 vs Wi-Fi 6E guide covers upgrades.

Step 2: Ping your router

Open Command Prompt or Terminal and find your router's address with ipconfig (it's listed as the Default Gateway, often something like 192.168.1.1 or 192.168.0.1). Then run:

ping 192.168.1.1 -n 100

Replace the address with your own. Microsoft's documentation says ping sends four requests by default; -n sets how many to send, and -t keeps pinging until you stop it with Ctrl+C. At the end you'll see how many packets were lost and the minimum, maximum and average times.

On a wired connection, replies from your own router should be quick and consistent, with no loss. If you see loss or big spikes here, the problem is inside your home: the cable, Wi-Fi, router or your PC's network adapter.

Step 3: Ping something on the internet

Next, ping a well-known site for the same number of requests, for example:

ping www.microsoft.com -n 100

If your router was clean but this shows loss or large spikes, the problem is somewhere between your router and the wider internet, which usually means your broadband line or provider. Try it at different times of day: if it only happens in the evening, congestion is a likely cause.

Step 4: Find where the loss starts with pathping

pathping is the most useful tool here. Microsoft describes it as showing latency and packet loss at each hop between you and a destination. Run:

pathping -n www.microsoft.com

The -n option skips looking up router names, which speeds it up. Pathping first lists the route, then spends a while gathering statistics (Microsoft says about 90 seconds, depending on the number of hops; by default it sends 100 queries to each router), then shows a table.

How to read it, according to Microsoft:

  • Loss on a link (shown against a vertical bar | in the address column) means congestion that is dropping traffic being forwarded along the path.

  • Loss shown against a router's own address can mean that router is overloaded, but if later hops show no loss, that router simply isn't replying to pings addressed to it and is still forwarding your traffic normally.

  • Loss that starts at one hop and continues all the way to the end is the real problem, and the hop where it starts tells you where.

If the loss starts at hop 1, it's your home network. If it starts at the first hops beyond your router, it's likely your provider. Rows of asterisks in tracert don't necessarily mean a problem either: Microsoft notes some routers don't return the messages tracert relies on.

Step 5: Stop things competing for bandwidth

If ping only spikes at certain times, check for other traffic. Large game downloads, cloud backups, video streaming on other devices and Windows updates can all fill your connection. Pause them while you play, and check whether your router has a quality of service (QoS) or gaming mode that prioritises your PC. Steam's download settings let you limit download speed.

Step 6: Reset Windows networking and update drivers

If the problem is on your PC, Microsoft's network troubleshooting guide suggests these commands in an administrator Command Prompt, in this order:

netsh winsock reset
netsh int ip reset
ipconfig /release
ipconfig /renew
ipconfig /flushdns

Restart afterwards. If that doesn't help, Microsoft suggests uninstalling the network adapter driver and restarting so Windows reinstalls it, or using Network reset under Settings > Network & internet > Advanced network settings, which removes and reinstalls your network adapters with default settings. Microsoft notes you might need to reinstall and set up VPN software afterwards. Downloading the latest LAN or Wi-Fi driver from your motherboard maker can also help; our chipset driver guide explains where to find them.

Step 7: Check your router and cables

  • Restart your router and modem.

  • Swap the Ethernet cable, and try a different port on the router.

  • Check the router's status page for the line speed and any errors, and install firmware updates.

  • If your PC has a 2.5GbE port and your router supports it, see our 2.5GbE vs 1GbE guide, though faster Ethernet won't fix packet loss on its own.

Step 8: Contact your provider with evidence

If pathping shows loss starting beyond your router on a wired connection, and resetting your router doesn't help, contact your broadband provider. Save the pathping output and ping results from different times of day; it's much easier to get a fault investigated with evidence than with "my games lag".

Our verdict

Don't guess at lag. Test wired first, ping your router, ping the internet, then run pathping to see where loss begins. Problems inside your home are usually Wi-Fi, cables or drivers and can be fixed yourself; loss that starts beyond your router is for your provider to sort out, and pathping results give you the evidence to prove it. Forge PC has not tested specific networks for this guide.

The bottom line

Don't guess at lag. Test wired first, ping your router, ping the internet, then run pathping to see where loss begins. Problems inside your home are usually Wi-Fi, cables or drivers and can be fixed yourself; loss that starts beyond your router is for your provider to sort out, and pathping results give you the evidence to prove it. Forge PC has not tested specific networks for this guide.

Sources

  1. 01Microsoft Learn, ping
  2. 02Microsoft Learn, pathping
  3. 03Microsoft Learn, tracert
  4. 04Microsoft Support, Fix Wi-Fi connection issues in Windows

About the author

Forge PC Staff

Editorial team

The shared byline for articles researched, written and edited by the Forge PC editorial team. How we source, check and correct our work is set out in our editorial policy.

More from Forge PC Staff

Read next

Best Wi-Fi 7 PCIe Card for Desktop PCs in 2026

Best Picks

Best Wi-Fi 7 PCIe Card for Desktop PCs in 2026

The TP-Link Archer TBE550E is the best Wi-Fi 7 PCIe card for most desktops: it works on AMD systems, supports 320MHz and MLO and was about £85 at Scan (17 Nov 2026), but it's Windows 11 only. The ASUS PCE-BE92BT (about £51) suits recent Intel PCs only. The ASUS PCE-BE6500 (about £34) is the budget pick.

Forge PC Staff4 min

How to Change DNS Servers in Windows 11 (and Turn On DNS over HTTPS)

How-To

How to Change DNS Servers in Windows 11 (and Turn On DNS over HTTPS)

To change DNS in Windows 11, open Settings > Network & internet, pick Ethernet or Wi-Fi, select Edit next to DNS server assignment, switch to Manual and enter addresses such as Cloudflare's 1.1.1.1 and 1.0.0.1, Google's 8.8.8.8 or Quad9's 9.9.9.9. Turn on DNS over HTTPS, check with ipconfig /all, and revert if public Wi-Fi logins fail.

Forge PC Staff3 min

How to Use Ollama From Another PC or Laptop on Your Home Network

How-To

How to Use Ollama From Another PC or Laptop on Your Home Network

Ollama only listens on 127.0.0.1 port 11434 by default. To use it from a laptop or another PC, quit Ollama, set the OLLAMA_HOST environment variable to 0.0.0.0:11434, restart it and point your app at your PC's local IP address. Allow it on private networks only and never forward the port to the internet.

Forge PC Staff2 min

Wi-Fi Keeps Disconnecting in Windows 11? How to Fix It

How-To

Wi-Fi Keeps Disconnecting in Windows 11? How to Fix It

How to stop Wi-Fi disconnecting in Windows 11: run the Network troubleshooter, forget and rejoin the network, restart the router, try the other band, stop Windows turning off the adapter to save power, reset the network stack, reinstall the driver and use network reset as a last resort.

Forge PC Staff4 min