Skip to content

How-ToMotherboard

How to Install a Graphics Card: Step-by-Step GPU Upgrade Guide

Before fitting a graphics card, check your PSU wattage and connectors, the card's size and a free PCIe x16 slot. Unplug the PC, release the slot latch to remove the old card, push the new one into the top x16 slot until it clicks, screw it in, use a separate cable for each power socket and plug your monitor into the card.

By , Editorial team

5 min read

How to Install a Graphics Card: Step-by-Step GPU Upgrade Guide

A graphics card upgrade is often the single biggest boost you can give a gaming PC, and physically fitting one takes only a few minutes. Most problems come from what happens around the installation: a power supply that isn't up to the job, power cables connected the wrong way, the card in the wrong slot, or a monitor cable still plugged into the motherboard.

This guide walks through the whole process, from checking compatibility to installing drivers. Forge PC hasn't photographed or timed an installation for this article; the steps follow ASUS's and Intel's official installation guidance, with NZXT's advice on display connections.

Before you buy: check it will fit and you can power it

  1. Check your power supply. Graphics card makers list a recommended PSU wattage on each card's spec page. ASUS tells you to confirm the recommended PSU for your card on its official website before installing. For example, Intel lists a 600W minimum with a PCIe 8-pin cable for its Arc B580 Limited Edition. Our PSU buying guide explains how to size a power supply.

  2. Check the power connectors. Count the 8-pin or 6-pin PCIe connectors on the card, or check whether it uses a 12V-2x6 connector, and make sure your PSU has enough separate cables. For 12V-2x6 cards, read how to connect a 12V-2x6 cable safely.

  3. Measure the space. Check the card's length, height and thickness against your case's maximum GPU length and the room below the slot. Intel's B580 guide lists 272 x 115 x 44mm for that card and recommends one extra slot of clearance in front of and behind the card for airflow.

  4. Check the slot. You need a full-size PCIe x16 slot. Intel's Arc B580, for instance, needs PCIe 3.0 or newer.

  5. Check your platform. Some cards rely on Resizable BAR for full performance. Intel says Resizable BAR must be enabled for optimal performance with Arc B-series cards, and that the operating system must use UEFI boot mode with a GPT partition style, with CSM disabled.

If you're choosing a card, see our best graphics card guide.

What you'll need

  • A Phillips screwdriver.

  • Somewhere clean and well lit to work.

  • Your new card and its power requirements.

  • Optionally, a support bracket for a heavy card.

Step 1: Prepare the PC and remove the old card

  1. Uninstall old drivers if you're switching brands. If you're moving between NVIDIA, AMD and Intel, it's worth removing the old driver first. Our guide to clean installing graphics drivers with DDU explains how.

  2. Shut down and unplug. ASUS says the system's power cable must be removed when installing or removing a graphics card. Intel's safety guidance also says to disconnect power before installing, servicing or removing a card, and to wait more than five minutes after turning the system off for hot parts to cool.

  3. Take ESD precautions. Intel advises proper electrostatic discharge precautions, such as ground straps and ESD mats.

  4. Open the case and lay it on its side so the motherboard is flat.

  5. Remove the old card. ASUS's order is: unplug the card's power cables, press down the latch at the end of the PCIe slot, then lift the card out vertically. You'll also need to remove the screws holding its bracket to the case first.

Step 2: Install the new card

  1. Choose the right slot. ASUS says to install your first graphics card in the top PCIe x16 slot (PCIEX16_1 on its boards).

  2. Remove the slot covers. Take out the metal expansion slot covers on the back of the case to match the width of your card.

  3. Line it up and push down. ASUS says to align the card's notch with the PCIe slot and push the card vertically down into the slot until it's firmly inserted. The slot's latch locks automatically when the card is fully seated.

  4. Screw it in. Secure the card's bracket to the case with screws.

  5. Support heavy cards. ASUS notes that graphics cards are heavy and that a graphics card bracket can help hold the card in place.

Step 3: Connect the power cables

If the card has power sockets, connect them to your power supply. This is the step that matters most.

  • Use a separate cable for each socket. ASUS says that if a card has two or more power sockets, each should be connected to its own PSU port. Don't use one cable with two plugs (a "daisy chain") to feed two sockets on the card.

  • Push connectors fully home. Make sure each plug is fully inserted before you close the case.

  • Check the card's requirements. Intel, for example, says its Arc A-series Limited Edition cards need a minimum 600W power supply with two PCIe power connectors, one 8-pin and one 6-pin, and that power supply requirements may vary, so check with the manufacturer.

Step 4: Connect your monitor to the card

Plug the display cable into the graphics card, not the motherboard. NZXT's support guide says the display cable must run between the monitor and the ports on the back of the graphics card, and it recommends DisplayPort, especially for monitors with higher refresh rates. Make sure the monitor's input setting matches the port you used.

Step 5: First boot and drivers

  1. Close the case, reconnect power and switch on.

  2. Check the BIOS if needed. For Intel Arc and other cards that benefit from Resizable BAR, Intel says to enable Above 4G Decoding and Re-Size BAR Support in the BIOS. Our guide to enabling Resizable BAR covers the steps for each board maker.

  3. Install the latest driver from NVIDIA, AMD or Intel. See how to update graphics drivers.

If something goes wrong

  • The PC won't power on. ASUS's advice is to remove the power cable, reseat the card and its power connectors, and check again.

  • No picture. Check the monitor cable is in the graphics card and the monitor's input is correct. Our no display fix guide goes through the rest.

  • The system won't boot with another card in the top slot. ASUS says its PCIEX16_1 slot supports graphics cards and storage devices only; move any other expansion card to a different slot.

  • Windows doesn't see the card. Try the steps in our graphics card not detected guide.

Our verdict

Installing a graphics card is straightforward if you check the essentials first: your PSU's wattage and connectors, the card's size, a free PCIe x16 slot and, for some cards, Resizable BAR support. Unplug the PC, remove the old card by releasing the slot latch, push the new card into the top x16 slot until the latch clicks, screw it in, connect each power socket with its own cable, and plug your monitor into the card. Then install the latest driver. Forge PC hasn't photographed or timed an installation for this guide; the steps follow ASUS's and Intel's official guidance.

The bottom line

Installing a graphics card is straightforward if you check the essentials first: your PSU's wattage and connectors, the card's size, a free PCIe x16 slot and, for some cards, Resizable BAR support. Unplug the PC, remove the old card by releasing the slot latch, push the new card into the top x16 slot until the latch clicks, screw it in, connect each power socket with its own cable, and plug your monitor into the card. Then install the latest driver. Forge PC hasn't photographed or timed an installation for this guide; the steps follow ASUS's and Intel's official guidance.

In this article

Sources

  1. 01ASUS, How to install Graphics Card on Motherboard?
  2. 02Intel, Intel Arc Graphics Desktop Quick Start Guide
  3. 03NZXT Support, My PC has no display, what can I do?

About the author

Forge PC Staff

Editorial team

The shared byline for articles researched, written and edited by the Forge PC editorial team. How we source, check and correct our work is set out in our editorial policy.

More from Forge PC Staff

Read next

How to Enable AMD Fluid Motion Frames (AFMF 2.1) on a Radeon Graphics Card

How-To

How to Enable AMD Fluid Motion Frames (AFMF 2.1) on a Radeon Graphics Card

To enable AMD Fluid Motion Frames, install Adrenalin 25.3.1 or newer, then select the HYPR-RX profile (RX 7000 and newer) or turn on AMD Fluid Motion Frames under Gaming > Graphics, globally or per game. AFMF 2.1 works on RX 6000 cards and newer in DirectX 11, DirectX 12, Vulkan and OpenGL games, with VSync off; RX 6000 cards need exclusive full screen.

Forge PC Staff2 min

Two vs Four RAM Sticks for DDR5: Why 2x32GB Usually Beats 4x16GB

Versus

Two vs Four RAM Sticks for DDR5: Why 2x32GB Usually Beats 4x16GB

Two DDR5 sticks are better for most builds. AMD lists DDR5-5600 as the AM5 maximum with two modules but DDR5-3600 with four, and XMP or EXPO speeds above that are overclocking and not guaranteed. Buy 2x16GB or 2x32GB for 32GB or 64GB, and use four sticks, ideally a matched kit, only if you need 128GB or more.

Forge PC Staff3 min

Best Wi-Fi 7 PCIe Card for Desktop PCs in 2026

Best Picks

Best Wi-Fi 7 PCIe Card for Desktop PCs in 2026

The TP-Link Archer TBE550E is the best Wi-Fi 7 PCIe card for most desktops: it works on AMD systems, supports 320MHz and MLO and was about £85 at Scan (17 Nov 2026), but it's Windows 11 only. The ASUS PCE-BE92BT (about £51) suits recent Intel PCs only. The ASUS PCE-BE6500 (about £34) is the budget pick.

Forge PC Staff4 min

AMD's FSR 4.1.2 Unreal Engine 5 Plugin Brings ML Upscaling to RX 6000 Cards

News

AMD's FSR 4.1.2 Unreal Engine 5 Plugin Brings ML Upscaling to RX 6000 Cards

AMD's FSR Unreal Engine 5 plugin now uses FSR Upscaling 4.1.2, bringing ML-based upscaling to Radeon RX 6000 cards and select Ryzen integrated graphics as well as RX 7000 and RX 9000, in UE 5.3 to 5.8 games that adopt it. It's DirectX 12 only for now and adds Frame Generation 4.0.2 with driver-assisted frame pacing on RX 9000 cards.

Forge PC Staff2 min