Skip to content

How-ToMotherboard

How to Fix 'CPU Fan Error! Press F1' on Startup

'CPU Fan Error! Press F1' usually means the cooler is on the wrong header, the fan spins below the BIOS low-speed threshold, or an AIO isn't reporting a speed on CPU_FAN. Check the fan or pump is spinning, move the cable to CPU_FAN, lower the fan speed low limit and update the BIOS. Only ignore the warning once you're sure the CPU is cooled.

By , Editorial team

5 min read

How to Fix 'CPU Fan Error! Press F1' on Startup

A "CPU Fan Error" message during startup, usually followed by "Press F1 to Run Setup", stops your PC at the boot screen until you press a key. ASUS's support documentation says the message means the system doesn't detect the fan, and in most cases the cause is simple: the cooler is plugged into the wrong header, the fan spins slower than the BIOS expects, or you've fitted an AIO liquid cooler. This guide is based on ASUS's official troubleshooting steps, and menu names on MSI, Gigabyte and ASRock boards differ a little. Forge PC hasn't tested every motherboard, so check your board's manual for the exact names. The one rule that matters most: make sure the CPU is actually being cooled before you silence the warning.

Step 0: Check that the cooler is working

Before you change any settings, take the side panel off and power on the PC.

  • Air cooler: is the fan spinning? If it isn't, switch off at the wall straight away and check the cable.

  • AIO liquid cooler: are the radiator fans spinning, and can you feel or hear the pump running? Many pumps have a lit logo that shows they have power.

If the fan or pump isn't running, don't use the PC until it's fixed. A CPU without working cooling can overheat; our overheating guide explains the symptoms.

Step 1: Check the cooler is mounted and plugged into CPU_FAN

ASUS's first two steps are to make sure the CPU fan is installed in the right position with its screws tight, and that the fan cable is securely connected to the CPU_FAN header rather than a chassis fan header (CHA_FAN).

ASUS says the error means the system doesn't detect the fan, so if your CPU fan is plugged into a case fan header and nothing is on CPU_FAN, you can get the error even though the fan is spinning.

  1. Switch off and unplug the PC.

  2. Follow the cooler fan's cable back to the motherboard and find the header it's plugged into. Your motherboard manual's layout diagram shows where CPU_FAN is.

  3. Push the connector firmly on to CPU_FAN. If your cooler has two fans, follow the cooler's manual for connecting the second one.

If you're not sure which board you have, our guide to finding your motherboard model will tell you, so you can download the manual.

Step 2: AIO liquid coolers

With an AIO, the pump and radiator fans may be connected to headers other than CPU_FAN, so the board may not detect a fan there. There are two fixes:

  • Check the cooler's wiring. Follow your cooler's manual for which headers the pump and fans should use; our AIO installation guide explains the usual layout.

  • Tell the BIOS to ignore the CPU fan reading. ASUS says you can set the CPU fan speed setting to Ignore if your computer already has a liquid cooling system. Only do this once you've confirmed the pump and fans are running, because the board will no longer warn you if they stop.

Step 3: Lower the CPU fan speed low limit

ASUS notes that if you install another brand of CPU fan with a lower rotation speed, the system may not be able to detect it.

On ASUS boards, ASUS's fix is to set CPU Fan Speed Low Limit to 200 RPM in the BIOS:

  1. Restart and press Del (or the key your board shows) to enter the BIOS.

  2. Find CPU Fan Speed Low Limit (on ASUS boards, fan monitoring settings are in the Monitor section).

  3. Set it to 200 RPM, then save and exit.

ASUS adds that this option only appears when CPU Q-Fan Control is set to DC Mode, PWM Mode or Auto (or, on older boards, Enabled, Advance Mode or Auto). Other brands have similar settings for a CPU fan fail warning or speed limit; check your manual. While you're in there, our fan curve guide shows how to tune fan speeds sensibly, and our PWM vs DC fans explainer covers which control mode to choose.

Step 4: Set the CPU fan reading to Ignore (only if you're sure)

ASUS also says you can set Monitor > CPU FAN Speed to Ignore if you don't want to open the case. That removes the warning, but it also removes the protection: the board won't warn you if the fan genuinely fails. Use it only when you know the cooling works, for example with an AIO whose pump and fans are on other headers, or a fanless cooler setup you've planned for.

Step 5: Update the BIOS

ASUS's last listed step is to update the BIOS to the latest version. Newer firmware can improve fan detection and compatibility. Follow our safe BIOS update guide and don't switch off during the update.

Other reasons you might need to press F1

ASUS's guide to F1 boot errors lists other messages that stop boot in the same way, so read the message carefully:

  • CMOS battery problems: ASUS says that if the CMOS battery is malfunctioning or has no power left, it needs replacing. Our clear CMOS guide covers resetting the BIOS too.

  • Overclocking failed: ASUS advises adjusting the overclock or restoring BIOS defaults.

  • S.M.A.R.T. status bad: a drive is warning that it may be failing. Back up immediately and see our SSD health guide.

  • USB device over current: ASUS suggests removing all USB devices, then adding them back one at a time to find the faulty one.

ASUS boards also have a Boot > Wait for F1 if there is error option that you can set to Disabled to stop the prompt. Treat that as a last resort, not a fix: it hides the warning rather than solving the cause.

Check temperatures afterwards

Once the PC boots normally, confirm the cooler is doing its job. Our guide to monitoring temperatures with HWiNFO and MSI Afterburner shows how to watch CPU temperature and fan speed under load. If temperatures are high even with the fan spinning, check the cooler is mounted firmly (ASUS's first step) and consider fresh thermal paste; see how to replace CPU thermal paste.

Our verdict

"CPU Fan Error" almost always comes down to three things: the cooler is on the wrong header, the fan spins too slowly for the BIOS threshold, or an AIO isn't reporting a fan speed on CPU_FAN. Check the fan or pump is running first, move the cable to CPU_FAN, lower the fan speed low limit (200 RPM on ASUS boards) and update the BIOS. Only set the reading to Ignore or disable the F1 prompt once you're certain the CPU is properly cooled.

The bottom line

"CPU Fan Error" almost always comes down to three things: the cooler is on the wrong header, the fan spins too slowly for the BIOS threshold, or an AIO isn't reporting a fan speed on CPU_FAN. Check the fan or pump is running first, move the cable to CPU_FAN, lower the fan speed low limit (200 RPM on ASUS boards) and update the BIOS. Only set the reading to Ignore or disable the F1 prompt once you're certain the CPU is properly cooled.

Sources

  1. 01ASUS Support, [Motherboard] Why I see the error message "CPU FAN Error" in POST?
  2. 02ASUS Support, [Motherboard] Error shows when I boot the system, need to press F1 to enter operation system

About the author

Forge PC Staff

Editorial team

The shared byline for articles researched, written and edited by the Forge PC editorial team. How we source, check and correct our work is set out in our editorial policy.

More from Forge PC Staff

Read next

How to Completely Uninstall ASUS Armoury Crate (and Stop It Reinstalling)

How-To

How to Completely Uninstall ASUS Armoury Crate (and Stop It Reinstalling)

Removing Armoury Crate from Settings leaves services behind. Use ASUS's Armoury Crate Uninstall Tool from your board's Driver & Utility page, restart and run it again if it reports a failure. Then disable 'Download & Install ARMOURY CRATE app' in the BIOS Tool menu so you're not prompted to reinstall it, and set fan curves in the BIOS instead.

Forge PC Staff4 min

How to Install an AIO Liquid CPU Cooler: Step-by-Step Guide

How-To

How to Install an AIO Liquid CPU Cooler: Step-by-Step Guide

Plan the radiator position first, ideally top-mounted as exhaust with its highest point above the pump. Fit the socket hardware with the board out of the case, connect hard-to-reach cables before mounting the pump, tighten the pump screws evenly in an X pattern, plug the pump into AIO_PUMP and set it to full speed in the BIOS.

Forge PC Staff5 min

How to Reactivate Windows 11 After Changing Your Motherboard or Other Hardware

How-To

How to Reactivate Windows 11 After Changing Your Motherboard or Other Hardware

A motherboard swap can deactivate Windows 11. Before you change it, link your licence to your Microsoft account. Afterwards, go to Settings > System > Activation > Troubleshoot, choose I changed hardware on this device recently, sign in and pick This is the device I'm using right now. Preinstalled OEM licences may need a new licence.

Forge PC Staff4 min