If your PC roars as soon as you open a web browser, or its fans keep revving up and down, the problem is usually the fan curve: the rule that tells each fan how fast to spin at a given temperature. Setting your own takes about 15 minutes and is one of the cheapest ways to make a PC quieter.
Forge PC has not produced new test results for this guide. The BIOS steps use ASUS's official BIOS manual for its AMD 800-series motherboards as an example, and the software steps follow the official documentation for FanControl, a free Windows app, checked on 14 November 2026. Other motherboard brands use different menu names but the same ideas. The example curve is a starting point, not a measured result.
Fan curve basics
A fan curve is a graph with temperature along the bottom and fan speed (as a percentage, or "duty cycle") up the side. You set a few points, and the fan speeds up smoothly between them.
Three things matter:
The temperature source. Each fan follows one sensor. CPU coolers should follow the CPU. Case fans often work better following the motherboard or the hotter of the CPU and graphics card, so they ramp up when you game.
The control type. 4-pin fans use PWM control; 3-pin fans are controlled by DC voltage. Setting the wrong mode can leave a fan stuck at full speed.
Smoothing. Processors spike in temperature for a second or two when you open an app. Without a delay, fans chase those spikes and the noise goes up and down, which is more annoying than a steady hum.
Method 1: Set fan curves in the BIOS
Setting curves in the BIOS works without any software running in Windows, which makes it the most reliable option. We use ASUS as an example; MSI, Gigabyte and ASRock boards have similar tools under names such as Smart Fan.
Enter the BIOS by pressing Delete or F2 as the PC starts. Our BIOS update guide has more on getting around it.
Open QFan Control. ASUS's manual says you can click the Qfan button above the menu bar or press F6. Advanced settings are under Monitor > Q-Fan Configuration.
Run Q-Fan Tuning first. This automatically finds the lowest speed each fan can run at and sets its minimum duty cycle. ASUS says it takes 2 to 5 minutes and warns not to shut down or reset your PC while it runs.
Set the control mode. ASUS's options are Auto Detect, DC Mode for 3-pin fans and pumps, and PWM Mode for 4-pin ones. Auto Detect is usually fine; switch manually if a fan will not change speed.
Choose a profile: ASUS offers Standard, Silent, Turbo, Full Speed and Manual. Try Silent first. Choose Manual to draw your own curve by dragging the points, then click Apply.
Pick the temperature source. For chassis fans, ASUS's options include CPU, CPU Package, MotherBoard, VRM, T_Sensor and Multiple Sources, which lets you choose up to three sensors and follows whichever is hottest.
Add smoothing. Step Up and Step Down have levels 0 to 5. Level 0 changes speed instantly; higher levels change more slowly, which ASUS says can reduce noise but also slows heat removal. Level 2 or 3 is a reasonable start.
Save and exit (usually F10).
ASUS adds an important safety note for manual CPU fan curves: it suggests raising the fan or pump to 100% if your CPU temperature goes above 75°C, and warns that the CPU will throttle if cooling is inadequate.
Method 2: Use FanControl in Windows
FanControl is a free, highly customisable fan app for Windows 10 and Windows 11, developed by Rem0o. The program itself is closed source, but it uses the open-source LibreHardwareMonitor library to read sensors. It can do things most BIOSes cannot, such as making case fans follow your graphics card temperature, and it can control many graphics card fans too.
Before installing, the FanControl FAQ recommends avoiding "smart" fan control in your BIOS. A fixed default speed, such as 50%, works best for most people, and you should check whether each header uses PWM or DC mode. That way the BIOS gives FanControl a steady baseline to work from.
Install it from the official site or GitHub releases, or from a terminal with:
winget install Rem0o.FanControl
Follow the guided setup on first launch. It detects and pairs your fans with their controls.
Calibrate. Calibration measures each fan's speed range. Newer versions also let you set "avoid points", speeds you never want a fan to sit at because they rattle or hum.
Create a curve. Add a Graph curve, pick its temperature sensor (for example CPU Package, or your GPU's temperature) and drag the points.
Assign curves to fans in each fan's control card.
Tune response. FanControl's advanced settings include steps, start %, stop %, response time and hysteresis. Hysteresis stops fans reacting to small temperature changes, which cures most revving.
Mix curves if you want case fans to follow the hotter of the CPU and graphics card. FanControl can combine curves or sensors using the maximum, minimum or average.
Set it to start with Windows so your curves apply after every reboot.
Things to know about FanControl
Anti-virus warnings are fixed in new versions. FanControl V238 and later use a PawnIO build of LibreHardwareMonitor instead of the old WinRing0 driver, which was the cause of earlier anti-virus warnings. Download the current version (V285 was listed on the official site on 14 November 2026).
Laptops are mostly unsupported. The FAQ says laptops usually do not expose their fans the way desktop motherboards do, though some brands have plugins.
NVIDIA graphics cards may not go below 30% or reach 0 RPM through FanControl; the project's wiki explains this limitation.
AMD graphics cards: FanControl's documentation warns that any fan setting it applies resets your Adrenalin overclocking settings to default, and that AMD cards have a set temperature for zero-RPM mode that you need to account for in your curve.
A sensible starting curve
These are reasonable starting points for a desktop with a tower cooler or an all-in-one liquid cooler. They are not test results; adjust them to your own hardware and ears.
CPU temperature | CPU fan / radiator fans | Case fans |
|---|
Up to 40°C | 25-30% | 25-30% |
60°C | 40-50% | 40% |
70°C | 60-70% | 55-60% |
80°C | 100% | 80-100% |
For all-in-one liquid coolers, many people run the pump at a fixed speed and put the curve on the radiator fans; check your cooler maker's guidance. If you find yourself hitting the top of the curve during normal gaming, look at airflow and dust before simply running fans faster.
Check the results
After setting your curves, run a game or a stress test and watch temperatures and fan speeds with HWiNFO, following our temperature monitoring guide. Our Cinebench and 3DMark guide is a handy way to apply a consistent load. If temperatures are still high, our PC overheating guide covers airflow and thermal paste, and an undervolted graphics card produces less heat in the first place.
Upgrading fans? Our best case fans and best CPU cooler guides have picks.
Our verdict
For most desktops, the simplest fix for a noisy PC is to set fan curves in the BIOS: run the automatic fan tuning, choose the right PWM or DC mode, start from a Silent profile and add a little step-up delay so fans stop chasing brief temperature spikes. If you want case fans to follow your graphics card, or finer control such as hysteresis and mixed curves, set a fixed speed in the BIOS and use the free FanControl app instead. Forge PC has not produced new test results for this guide; it follows ASUS's BIOS manual and FanControl's official documentation.