Skip to content

How-ToCase

How to Clean Dust Out of Your PC Safely (and How Often to Do It)

Switch off and unplug the PC, clean the dust filters first, then use short bursts of compressed air on fans, heatsinks, radiator fins and the PSU grille while holding each fan still so it can't overspin. Keep the can upright, brush fins gently, never open the PSU and don't vacuum inside the case. Check filters every month or two and clean inside every few months.

By , Editorial team

3 min read

How to Clean Dust Out of Your PC Safely (and How Often to Do It)

Dust is the slow way to lose cooling performance. It builds up on filters, fan blades, heatsinks and radiator fins until air can't get through, and your PC gradually runs hotter and louder. NZXT reckons a clean-out takes about 20 minutes, and it's one of the cheapest fixes for a noisy or hot PC.

Forge PC hasn't measured temperature changes for this guide. The steps follow cleaning guidance from NZXT and HP, checked on 17 November 2026. Always check your case and component manuals too.

Signs your PC needs cleaning

What you need

  • A can of compressed air or an electric air duster

  • A soft brush, such as a clean paintbrush or soft toothbrush

  • A microfibre cloth for the outside of the case (HP suggests a slightly damp one)

  • Optional: an anti-static wrist strap (HP recommends grounding yourself with one)

Step 1: Power down and open the case

Shut down Windows, switch the power supply off at the back (the O position) and unplug the power cable. NZXT recommends touching the metal case to discharge static before you reach inside. Then remove the side panel.

Step 2: Clean the dust filters first

Filters catch most of the dust, so they need the most attention. Most cases have them at the front, top or bottom; your case manual shows where. NZXT says you can brush removable filters or blow them out with compressed air, and that most mesh filters can be rinsed under the tap. Let them dry completely before refitting them.

Step 3: Clean the fans

  • Hold each fan still with a finger before you blow air at it. NZXT warns that compressed air can spin a fan far faster than it's designed to run, which can damage its bearings. HP gives the same advice.

  • Use short bursts, not one long blast.

  • Keep the can upright. NZXT notes that a tilted can can spray freezing liquid propellant.

  • Wipe or brush off any dust stuck to the blades.

Step 4: Clean heatsinks and radiator fins

Radiator and heatsink fins trap the most dust, and it's where blockages hurt temperatures most. Blow compressed air through the fins, then lift what's left with a soft brush. NZXT suggests working from the side the air normally exits, to push dust back the way it came in. Go gently: fins are thin and bend easily, so don't use anything harder than a soft brush.

Do the same for the graphics card: hold its fans still and blow short bursts through its heatsink.

Step 5: The power supply

Blow dust out of the power supply's fan grille from the outside, usually at the bottom or back of the case. Never open the power supply. NZXT points out that it can hold a charge even when unplugged, and there's nothing inside you need to clean.

Step 6: Reassemble and check temperatures

Refit the filters and side panel, plug in, switch the PSU back on and start up. Compare temperatures with what you saw before. If they're still high after a clean, the problem may be elsewhere: see our how to stop your PC overheating guide, our case fan airflow guide, or consider replacing your CPU thermal paste.

Don't use a household vacuum inside the case

NZXT advises against vacuuming inside the PC: a household vacuum can build up static, and its nozzle can knock components. It's fine for filters you've removed from the case.

How often should you clean your PC?

NZXT suggests checking filters every month or two and giving the inside a full clean every few months. HP suggests deep-cleaning internal components every three to six months. Both say to clean more often if you have pets or a dusty room. The amount of dust on your filters is the best guide.

Our verdict

To clean dust out of your PC, switch off and unplug it, clean the filters first, then use short bursts of compressed air on the fans, heatsinks, radiator and PSU grille while holding each fan still so it can't overspin. Keep the can upright, brush stubborn dust off fins gently, never open the power supply and don't vacuum inside the case. Check filters every month or two and clean inside every few months, more often with pets. Forge PC hasn't measured temperature changes for this guide.

The bottom line

To clean dust out of your PC, switch off and unplug it, clean the filters first, then use short bursts of compressed air on the fans, heatsinks, radiator and PSU grille while holding each fan still so it can't overspin. Keep the can upright, brush stubborn dust off fins gently, never open the power supply and don't vacuum inside the case. Check filters every month or two and clean inside every few months, more often with pets. Forge PC hasn't measured temperature changes for this guide.

Sources

  1. 01NZXT, How to Clean Dust Out of Your PC Safely
  2. 02HP, The Complete Guide to Clean Your Computer: Inside and Out

About the author

Forge PC Staff

Editorial team

The shared byline for articles researched, written and edited by the Forge PC editorial team. How we source, check and correct our work is set out in our editorial policy.

More from Forge PC Staff

Read next

SFX vs SFX-L vs ATX Power Supply: Which PSU Size Do You Need?

Versus

SFX vs SFX-L vs ATX Power Supply: Which PSU Size Do You Need?

ATX power supplies are 150 x 86mm with a depth of 140mm or more; SFX units are 125 x 63.5 x 100mm and SFX-L units are 125 x 63.5 x 130mm. Buy ATX for normal towers, SFX for compact mini-ITX cases and SFX-L only if your case supports it. An SFX unit can fit an ATX case with a bracket, but an ATX unit won't fit an SFX-only case.

Forge PC Staff4 min

Liquid Metal vs Thermal Paste: Is Liquid Metal Worth the Risk for Your CPU?

Versus

Liquid Metal vs Thermal Paste: Is Liquid Metal Worth the Risk for Your CPU?

Thermal paste is the right choice for almost everyone: it's cheap, easy and non-conductive. Liquid metal such as Thermal Grizzly Conductonaut targets maximum heat transfer but is electrically conductive, must never touch aluminium, can react with bare copper and needs insulation and checking. Use it only if you're experienced, ideally on nickel-plated copper or direct-die setups.

Forge PC Staff4 min

ARGB vs RGB: 5V 3-Pin and 12V 4-Pin Headers Explained (and How Not to Fry Them)

Versus

ARGB vs RGB: 5V 3-Pin and 12V 4-Pin Headers Explained (and How Not to Fry Them)

5V ARGB uses a 3-pin header and controls each LED individually for animations and gradients; 12V RGB uses a 4-pin header and shows one colour at a time. They aren't interchangeable, and plugging either into the wrong header can permanently damage the lighting, the motherboard or both. Check the pin count and the board label, and use a controller if needed.

Forge PC Staff4 min