Skip to content

VersusGPU

ATX 3.1 vs ATX 3.0 Power Supplies: What Changed and Does It Matter?

ATX 3.1 replaces ATX 3.0's 12VHPWR socket with the 12V-2x6 design, which has longer power pins and shorter sense pins so a loose plug delivers no power, and relaxes hold-up time to 12ms at full load. The cables are the same design, so a good ATX 3.0 PSU is still fine; buy ATX 3.1 if you're buying new.

By , Editorial team

3 min read

ATX 3.1 vs ATX 3.0 Power Supplies: What Changed and Does It Matter?
be quiet! Pure Power 13 M 1000W 80 Plus Gold Fully Modular ATX 3.1 PSU compared with Lian Li Edge Gold V2 850W 80 Plus Gold Fully Modular ATX 3.1 PSU (Black)
be quiet! Pure Power 13 M 1000W 80 Plus Gold Fully Modular ATX 3.1 PSULian Li Edge Gold V2 850W 80 Plus Gold Fully Modular ATX 3.1 PSU (Black)
Wattage (W)1000850
Efficiency Rating80+ Gold80+ Gold
Form Factor—ATX
Modular TypeFully ModularFully Modular
ATX Version / PCIe Power StandardATX 3.1ATX 3.1
Multi / Single RailSingle Rail—
Protections (OVP/OCP/OTP etc.)—OCP, OVP, OTP, OPP, SCP, UVP, SIP, NLP
6+2 PCIe Count4—
12VHPWR / 12V-2x6 Count11
SATA Power Count6—
PSU Length (mm)160182
Fan Size (mm)120120
Zero RPM ModeYesYes

If you're shopping for a power supply, most current models are labelled ATX 3.1, while some older stock still says ATX 3.0. Both standards were written with modern high-power graphics cards in mind, and in practice they are very close. This guide explains the real differences, using the published comparison tables from Seasonic and Cooler Master and Hardware Busters' analysis of the specification.

Forge PC hasn't lab-tested power supplies for this article; everything below comes from the manufacturers' and analysts' published explanations of the standard.

The short version

ATX 3.0

ATX 3.1

16-pin GPU connector name

12VHPWR

12V-2x6

Peak power excursion

200% for 100μs

200% for 100μs

Hold-up time at full load

17ms

12ms (17ms at 80% load recommended)

12V tolerance

-7% to +5%

-7% to +5%

Cable compatibility

Same modular cable design

Same modular cable design

Source: Seasonic's ATX standards comparison table.

The big change: 12VHPWR becomes 12V-2x6

ATX 3.0 introduced the 16-pin 12VHPWR connector for graphics cards that need more than 450W. ATX 3.1 replaces it with the 12V-2x6 connector. Hardware Busters, which analysed the ATX 3.1 and PCIe CEM 5.1 specifications when they were released on 13 September 2023, notes that the 12V-2x6 connector is still designed to deliver up to 600W.

The changes are on the socket side, mainly the graphics card's header:

  • Longer power pins and shorter sense pins. Cooler Master says the power pins were extended by 0.25mm and the signal (sense) pins shortened by 1.5mm.

  • A zero-watt state. Hardware Busters explains that the sense pins now only make contact once the power pins are properly mated. If the card sees both sense pins open, it can draw no power at all, which is meant to stop a half-inserted plug from overheating.

  • Labels. Cooler Master says 12VHPWR parts are marked "H+" and 12V-2x6 parts "H++".

Seasonic stresses that the cables themselves did not change: the two connectors differ only in their socket design, and modular cables remain fully compatible. Cooler Master adds that mixing old and new parts works, but you won't get every safety benefit of ATX 3.1 unless both ends are the newer design.

Whichever standard you have, the most important thing is to push the plug fully home and avoid sharp bends near the connector. Our guide to connecting a 12V-2x6 cable safely walks through it.

Hold-up time: shorter on paper

Hold-up time is how long a PSU can keep its outputs within spec after the mains supply drops out. Seasonic's table shows ATX 3.1 relaxed the requirement from 17ms at full load to 12ms at full load, with 17ms at 80% load recommended. Seasonic says this is not a downgrade in practice, because the actual hold-up time depends on each product's own specification and test data. If it matters to you, for example on an unreliable supply, check the individual PSU's datasheet or pair it with a UPS.

What stayed the same

Both standards require the PSU to handle short power excursions of 200% of rated output for 100 microseconds, and share the same 12V voltage tolerance and light-load efficiency requirements, according to Seasonic's comparison. Those excursion rules were the main reason ATX 3.0 existed: modern graphics cards can briefly spike well above their average draw.

Which should you buy?

  • Buying new: an ATX 3.1 unit is the sensible default, because it has the updated connector design and is what most current models carry. Our best power supply, best 850W and best 1000W guides list current options.

  • Already own a good ATX 3.0 unit: there is no need to replace it just for the label. The cable is the same design, and the most important connector changes are on the graphics card's socket.

  • Older ATX 2.x unit with adapters: this is where an upgrade makes more sense if you're fitting a high-power card. See how to choose a PSU for sizing.

Wattage, efficiency rating and build quality matter far more than 3.0 vs 3.1. If you're weighing efficiency too, see 80 Plus Gold vs Platinum.

Our verdict

ATX 3.1 is a refinement, not a revolution. Its main change is the 12V-2x6 connector, with longer power pins and shorter sense pins so a badly seated plug delivers no power, plus a relaxed 12ms hold-up requirement. The cables are the same design, so a good ATX 3.0 PSU is still fine to keep. If you're buying new, choose ATX 3.1, but judge the unit on wattage, quality and warranty first. Forge PC hasn't tested these PSUs; the details come from Seasonic, Cooler Master and Hardware Busters.

The bottom line

ATX 3.1 is a refinement, not a revolution. Its main change is the 12V-2x6 connector, with longer power pins and shorter sense pins so a badly seated plug delivers no power, plus a relaxed 12ms hold-up requirement. The cables are the same design, so a good ATX 3.0 PSU is still fine to keep. If you're buying new, choose ATX 3.1, but judge the unit on wattage, quality and warranty first. Forge PC hasn't tested these PSUs; the details come from Seasonic, Cooler Master and Hardware Busters.

Sources

  1. 01Seasonic Knowledge Base, Differences Between ATX 3.0 and ATX 3.1 Standards
  2. 02Cooler Master, What is ATX 3.1?
  3. 03Hardware Busters, ATX v3.1 & PCIe CEM 5.1 are official!

About the author

Forge PC Staff

Editorial team

The shared byline for articles researched, written and edited by the Forge PC editorial team. How we source, check and correct our work is set out in our editorial policy.

More from Forge PC Staff

Read next

How to Enable AMD Fluid Motion Frames (AFMF 2.1) on a Radeon Graphics Card

How-To

How to Enable AMD Fluid Motion Frames (AFMF 2.1) on a Radeon Graphics Card

To enable AMD Fluid Motion Frames, install Adrenalin 25.3.1 or newer, then select the HYPR-RX profile (RX 7000 and newer) or turn on AMD Fluid Motion Frames under Gaming > Graphics, globally or per game. AFMF 2.1 works on RX 6000 cards and newer in DirectX 11, DirectX 12, Vulkan and OpenGL games, with VSync off; RX 6000 cards need exclusive full screen.

Forge PC Staff2 min

AMD's FSR 4.1.2 Unreal Engine 5 Plugin Brings ML Upscaling to RX 6000 Cards

News

AMD's FSR 4.1.2 Unreal Engine 5 Plugin Brings ML Upscaling to RX 6000 Cards

AMD's FSR Unreal Engine 5 plugin now uses FSR Upscaling 4.1.2, bringing ML-based upscaling to Radeon RX 6000 cards and select Ryzen integrated graphics as well as RX 7000 and RX 9000, in UE 5.3 to 5.8 games that adopt it. It's DirectX 12 only for now and adds Frame Generation 4.0.2 with driver-assisted frame pacing on RX 9000 cards.

Forge PC Staff2 min

NVIDIA's DGX Spark HPC Developer Kit Links Four Sparks Into a 512GB Desk-Side Cluster

News

NVIDIA's DGX Spark HPC Developer Kit Links Four Sparks Into a 512GB Desk-Side Cluster

NVIDIA's DGX Spark HPC Developer Kit, announced at SC26 on 16 November 2026, links four DGX Spark systems in a ring over ConnectX-7 with no network switch, for 512GB of combined memory and 20TB of NVMe storage. NVIDIA says it can spread models of up to 700B parameters across the nodes with NVFP4. No UK kit price yet; Scan sells two-Spark bundles at about £12,845.

Forge PC Staff3 min

SFX vs SFX-L vs ATX Power Supply: Which PSU Size Do You Need?

Versus

SFX vs SFX-L vs ATX Power Supply: Which PSU Size Do You Need?

ATX power supplies are 150 x 86mm with a depth of 140mm or more; SFX units are 125 x 63.5 x 100mm and SFX-L units are 125 x 63.5 x 130mm. Buy ATX for normal towers, SFX for compact mini-ITX cases and SFX-L only if your case supports it. An SFX unit can fit an ATX case with a bracket, but an ATX unit won't fit an SFX-only case.

Forge PC Staff4 min