Skip to content

How-ToCPU

How to Use PBO and Curve Optimizer on a Ryzen CPU (Safely)

Precision Boost Overdrive raises a Ryzen CPU's power and current limits so it can boost harder, and Curve Optimizer undervolts it so it runs cooler at the same clocks. Enable PBO with motherboard limits in Ryzen Master or the BIOS, start Curve Optimizer at -10 on all cores, then stress test and back off if unstable. AMD says PBO voids the CPU warranty.

By , Editorial team

4 min read

How to Use PBO and Curve Optimizer on a Ryzen CPU (Safely)

AMD's Ryzen processors already boost their clocks automatically, but two settings can give them more room. Precision Boost Overdrive (PBO) raises the power and current limits the CPU boosts within, and Curve Optimizer lowers the voltage each core needs at a given clock speed. Used together carefully, they can make a Ryzen chip run cooler and hold higher clocks for longer.

Forge PC hasn't tested specific settings on its own hardware. This guide follows AMD's Ryzen Master documentation and Tom's Hardware's step-by-step guide, and the results on your PC will depend on your particular chip, cooler and motherboard.

Before you start: the warranty catch

AMD classes PBO as overclocking. Its Ryzen Master page states that because PBO runs the processor "outside of specifications and in excess of factory settings", using it invalidates the AMD product warranty, and that AMD's warranty doesn't cover damage caused by overclocking. Tom's Hardware also notes the warning Ryzen Master shows every time you open it. If you're not comfortable with that, stop here: a stock Ryzen CPU is already well tuned.

You'll also want:

What PBO and Curve Optimizer actually do

Setting

What it changes

Effect

Precision Boost Overdrive

Raises the PPT (package power), TDC and EDC (current) limits, with an optional boost clock override

The CPU can boost harder and longer under heavy load

Curve Optimizer

Shifts each core's voltage-frequency curve; a negative value lowers voltage

Less heat and power at the same clocks, which can leave more headroom to boost

Tom's Hardware explains that in Ryzen Master's PBO mode the power and current limits are set automatically to motherboard limits, which the board's firmware decides based on its power delivery. The boost override can add up to +200MHz above the rated boost clock.

Curve Optimizer is an undervolt. Tom's Hardware points out that pushing it too far causes instability: random freezes, crashes or blue screens, especially under heavy load. Every chip is different because of the "silicon lottery", so one CPU may be stable at a value that crashes another.

Method 1: Ryzen Master (easiest)

AMD offers separate Ryzen Master downloads for different CPU generations; the current version is for Ryzen 5000 series processors and later.

  1. Download Ryzen Master from AMD's website, install it and restart if asked.

  2. Open it, accept the warning and switch to Advanced View.

  3. Choose a profile and select Precision Boost Overdrive. Start with PBO using the motherboard limits rather than entering your own power figures. Apply and let Ryzen Master run its quick check.

  4. Open the Curve Optimizer section. Tom's Hardware recommends applying the same offset to all cores to begin with, as it's less tedious than tuning each core.

  5. Choose a negative offset and start at -10. Apply it and let Ryzen Master run its short validation test.

  6. If it passes, save the profile, then test properly (see below). If it's stable, you can try lowering the value gradually, testing each time.

AMD notes that Ryzen Master can apply PBO and Curve Optimizer changes either on the fly or through the BIOS so that they stay in effect after a restart.

Method 2: In the BIOS

Most AM4 and AM5 motherboards put these settings under an AMD Overclocking or Precision Boost Overdrive menu, usually in the advanced or tweaker section. Names and locations vary by brand, so check your motherboard manual. The approach is the same: enable PBO, open Curve Optimizer, choose All Cores, set the sign to Negative and start with a small magnitude such as 10. Save and restart.

Test for stability

Ryzen Master's validation test is short. Tom's Hardware recommends a longer stress test to confirm an undervolt is genuinely stable, because real workloads behave differently from short synthetic tests. Run a demanding game or a benchmark such as Cinebench or Prime95, and watch temperatures, clock speeds and throttling while it runs. Our guides to stress testing a PC and running Cinebench and 3DMark walk through the tools.

Record a benchmark score before you change anything and compare it afterwards. Tom's Hardware says the score after undervolting should ideally improve by a small margin. If you get a crash, freeze or hardware error, make the offset less aggressive (closer to zero) and test again.

If the PC won't boot after a change in the BIOS, reset the settings by clearing the CMOS, then start again with a smaller offset.

Our verdict

PBO raises a Ryzen CPU's power and current limits so it can boost harder, and Curve Optimizer lowers its voltage so it runs cooler at the same clocks. Enable PBO with motherboard limits, start Curve Optimizer at -10 on all cores, then stress test properly and back off at the first sign of instability. Remember that AMD says using PBO voids the CPU warranty. Forge PC hasn't tested specific settings itself.

The bottom line

PBO raises a Ryzen CPU's power and current limits so it can boost harder, and Curve Optimizer lowers its voltage so it runs cooler at the same clocks. Enable PBO with motherboard limits, start Curve Optimizer at -10 on all cores, then stress test properly and back off at the first sign of instability. Remember that AMD says using PBO voids the CPU warranty. Forge PC hasn't tested specific settings itself.

Sources

  1. 01Tom's Hardware, How to use Precision Boost Overdrive and Curve Optimizer to improve Ryzen CPU performance
  2. 02AMD, AMD Ryzen Master Utility

About the author

Forge PC Staff

Editorial team

The shared byline for articles researched, written and edited by the Forge PC editorial team. How we source, check and correct our work is set out in our editorial policy.

More from Forge PC Staff

Read next

Two vs Four RAM Sticks for DDR5: Why 2x32GB Usually Beats 4x16GB

Versus

Two vs Four RAM Sticks for DDR5: Why 2x32GB Usually Beats 4x16GB

Two DDR5 sticks are better for most builds. AMD lists DDR5-5600 as the AM5 maximum with two modules but DDR5-3600 with four, and XMP or EXPO speeds above that are overclocking and not guaranteed. Buy 2x16GB or 2x32GB for 32GB or 64GB, and use four sticks, ideally a matched kit, only if you need 128GB or more.

Forge PC Staff3 min

Best Wi-Fi 7 PCIe Card for Desktop PCs in 2026

Best Picks

Best Wi-Fi 7 PCIe Card for Desktop PCs in 2026

The TP-Link Archer TBE550E is the best Wi-Fi 7 PCIe card for most desktops: it works on AMD systems, supports 320MHz and MLO and was about £85 at Scan (17 Nov 2026), but it's Windows 11 only. The ASUS PCE-BE92BT (about £51) suits recent Intel PCs only. The ASUS PCE-BE6500 (about £34) is the budget pick.

Forge PC Staff4 min

How to Change Your Mouse Polling Rate: 1,000Hz vs 4,000Hz vs 8,000Hz Explained

How-To

How to Change Your Mouse Polling Rate: 1,000Hz vs 4,000Hz vs 8,000Hz Explained

Change your mouse polling rate in the maker's software. 1,000Hz (1ms) is the safe default; 2,000-4,000Hz can feel slightly smoother; 8,000Hz (0.125ms) needs a six-core-plus CPU, a direct USB 3 port and at least 1,600 DPI to saturate. TechPowerUp measured small gains above 4,000Hz, and Razer advises dropping to 4,000Hz or 2,000Hz if you see stutter.

Forge PC Staff4 min

Liquid Metal vs Thermal Paste: Is Liquid Metal Worth the Risk for Your CPU?

Versus

Liquid Metal vs Thermal Paste: Is Liquid Metal Worth the Risk for Your CPU?

Thermal paste is the right choice for almost everyone: it's cheap, easy and non-conductive. Liquid metal such as Thermal Grizzly Conductonaut targets maximum heat transfer but is electrically conductive, must never touch aluminium, can react with bare copper and needs insulation and checking. Use it only if you're experienced, ideally on nickel-plated copper or direct-die setups.

Forge PC Staff4 min