Skip to content

How-ToOS

How to Set Up OBS Microphone Filters for Clearer Streams

OBS Studio's built-in audio filters can clean up your mic: Noise Suppression for fan hiss, a Noise Gate for silence between sentences, a Compressor near the start of the chain for loud moments and a Limiter last to stop clipping. Start from OBS's defaults.

By , Editorial team

3 min read

How to Set Up OBS Microphone Filters for Clearer Streams

A decent microphone gets you most of the way to good stream audio. OBS Studio's free audio filters do the rest: they can remove PC fan hiss, mute the background between sentences, even out loud and quiet moments and stop shouting from clipping. This guide is based on OBS's own Knowledge Base; Forge PC hasn't tested these settings on a particular microphone, so treat the values below as OBS's defaults and a starting point, not a recipe.

Step 1: Open the filters for your mic

  1. In OBS Studio, find your microphone in the Audio Mixer dock.

  2. Click the three-dot menu (or the cog) next to it and choose Filters.

  3. Click + under Audio Filters to add a filter. Filters run from top to bottom, and you can drag them to change the order.

If OBS can't hear your mic at all, start with how to fix a microphone not working in Windows 11.

The filters and what they do

OBS's Filters Guide lists these audio filters, among others:

Filter

What OBS says it does

OBS default

Gain

Boosts the volume of quiet audio sources

0.00dB

Noise Suppression

Removes mild background or white noise

RNNoise method

Noise Gate

Cuts background noise when you're not speaking

Close -32dB, open -26dB

Compressor

Makes loud sounds quieter; can also duck one source when another makes sound

10:1 ratio, -18dB threshold

Limiter

Prevents audio peaking above 0dB

-6.00dB threshold

Expander

Like a noise gate, with an adjustable ratio

-

A sensible order

OBS gives guidance on where some filters belong: the compressor "typically would be placed at or near the beginning of your filter chain" and the limiter "should be the last filter in your chain". A chain that follows that guidance (the order of the other filters is our suggestion, not OBS's) is:

  1. Noise Suppression

  2. Noise Gate

  3. Compressor

  4. Gain (only if you still need it)

  5. Limiter (always last)

Step 2: Noise Suppression

OBS says Noise Suppression works well on things like PC fan noise and other environmental hum, but isn't effective against large amounts of background noise, such as a loud room. Choose a method:

  • RNNoise (the default): higher quality, at the cost of more CPU use.

  • Speex: lighter and configurable with a suppression level slider (default -30dB). Move it further left for stronger suppression, but OBS warns that this can distort your voice.

  • NVIDIA Noise Removal: appears in the list once you've installed NVIDIA's Broadcast SDK redistributable. Our NVIDIA Broadcast vs AMD noise suppression comparison covers the GPU-based options.

Step 3: Noise Gate

The gate closes your mic when you stop talking. OBS's advice is to set the close threshold above your background noise level and the open threshold slightly below your speaking voice. Defaults are close -32dB, open -26dB, attack 25ms, hold 200ms and release 150ms. Watch the meter while you sit silently, then while you talk, and adjust. If the ends of words get cut off, lower the open threshold or lengthen the hold time.

Step 4: Compressor

OBS describes the compressor as useful when your mic is set for normal speech but sometimes spikes, such as when you shout. It lowers the volume above the threshold and then restores it. OBS's defaults are a 10:1 ratio, -18dB threshold, 6ms attack and 60ms release. OBS explains that 2:1 is weak compression and 6:1 much stronger. Because compression makes the signal quieter, use Output Gain to bring the average level back up.

Step 5: Limiter

Add a Limiter last. OBS describes it as a compressor with a very fast attack and very high ratio that stops your audio exceeding the threshold (default -6dB). It's your safety net against clipping and distortion.

Step 6: Gain, if needed

OBS says gain should generally be set at the source (your mic or interface) before it reaches OBS, and the Gain filter is for very quiet sources. Turn up your mic's input level in Windows or your audio interface first.

Check your levels

Record a short test with OBS Studio and listen back with headphones. Your voice should be clear and shouldn't hit the top of the mixer meter. If you're still choosing a mic, see the best microphones for streaming, dynamic vs condenser and USB vs XLR. For the rest of your setup, read how to set up a PC for streaming.

Our verdict

Add Noise Suppression, a Noise Gate, a Compressor and a Limiter to your mic in OBS, keeping the compressor near the start and the limiter last, as OBS recommends. Start from OBS's defaults, then adjust the gate thresholds and compressor while watching the meter.

The bottom line

Add Noise Suppression, a Noise Gate, a Compressor and a Limiter to your mic in OBS, keeping the compressor near the start and the limiter last, as OBS recommends. Start from OBS's defaults, then adjust the gate thresholds and compressor while watching the meter.

Sources

  1. 01OBS Studio Knowledge Base, Filters Guide
  2. 02OBS Studio Knowledge Base, Noise Suppression Filter
  3. 03OBS Studio Knowledge Base, Noise Gate Filter
  4. 04OBS Studio Knowledge Base, Compressor Filter
  5. 05OBS Studio Knowledge Base, Limiter Filter
  6. 06OBS Studio Knowledge Base, Gain Filter

About the author

Forge PC Staff

Editorial team

The shared byline for articles researched, written and edited by the Forge PC editorial team. How we source, check and correct our work is set out in our editorial policy.

More from Forge PC Staff

Read next

Best Free Keyboard and Mouse Remapping Software for Windows

Best Picks

Best Free Keyboard and Mouse Remapping Software for Windows in 2026

PowerToys Keyboard Manager is the best free remapping tool for most people. SharpKeys makes permanent key swaps with nothing running in the background, X-Mouse Button Control handles mouse buttons and per-app profiles, and AutoHotkey covers macros.

Forge PC Staff4 min

How to Use Ollama With Home Assistant for a Local AI Voice Assistant

How-To

How to Use Ollama With Home Assistant for a Local AI Voice Assistant

Home Assistant's Ollama integration lets a model on your own PC power Assist. Expose Ollama on your network with OLLAMA_HOST, add the integration with your server's URL, pick a tool-capable model and expose only the entities you want it to control.

Forge PC Staff3 min

How to Keep Ollama Models Loaded (or Unload Them to Free VRAM)

How-To

How to Keep Ollama Models Loaded (or Unload Them to Free VRAM)

Ollama unloads models five minutes after your last request. Use ollama ps to see what's loaded, ollama stop to free VRAM straight away, the keep_alive API parameter per request, and OLLAMA_KEEP_ALIVE or OLLAMA_MAX_LOADED_MODELS to change the defaults.

Forge PC Staff3 min

How to Test Your Home Network Speed With iperf3

How-To

How to Test Your Home Network Speed With iperf3

iperf3 measures the speed of your own network rather than your internet connection. Install it on two devices, run iperf3 -s on one and iperf3 -c with its IP address on the other, then use -R for the reverse direction and -P for parallel streams to find Wi-Fi, cable or port bottlenecks.

Forge PC Staff3 min