Skip to content

How-ToOS

How to Fix Ethernet Stuck at 100Mbps in Windows 11

If Windows 11 shows an Ethernet link speed of 100Mbps instead of 1Gbps, Intel says the cause is almost always a cable. Check the link speed in Settings, make sure Speed & Duplex is set to Auto Negotiation, then swap in a known-good Cat 6 cable plugged straight into the router before blaming switches, wall sockets or the motherboard port.

By , Editorial team

3 min read

How to Fix Ethernet Stuck at 100Mbps in Windows 11

You've paid for fast broadband, plugged your PC into the router with a cable, and downloads still won't go past about 12MB/s (100Mbps divided by eight bits per byte is 12.5MB/s, before overheads). A common reason is that your Ethernet link has dropped to 100Mbps instead of 1Gbps. This guide follows Intel's support advice for gigabit adapters capped at 100Mbps. Forge PC hasn't tested every network adapter, but the checks below apply to most desktop PCs.

In Windows 11:

  1. Open Settings > Network & internet and select your Ethernet connection.

  2. Look for Link speed (Receive/Transmit) in its properties.

You can also open Task Manager (Ctrl + Shift + Esc), go to the Performance tab and click Ethernet.

Or, as Intel describes, open Control Panel > Network and Internet > Network and Sharing Center, click your Ethernet connection, and read the Speed figure. A working gigabit link shows 1.0Gbps. If it shows 100Mbps, the adapter and the device at the other end have agreed on the slower speed.

A link speed of 1Gbps is the connection between your PC and the router or switch. It isn't your internet speed, which depends on your broadband plan.

Step 2: Check the adapter is set to Auto Negotiation

Intel says that for gigabit connections, the only setting that matters is that the adapter is set to Auto Negotiation, which is the default:

  1. Right-click Start and open Device Manager.

  2. Expand Network adapters, right-click your Ethernet adapter and choose Properties.

  3. On the Advanced tab, select Speed & Duplex and make sure it's set to Auto Negotiation.

Intel notes that some people expect to see a fixed "1.0Gbps Full Duplex" option, but on its Killer adapters there isn't one; Auto Negotiation is the correct setting. If you've forced a fixed speed in the past, set it back to Auto.

Step 3: Reseat and swap the cable

Intel says that if the setting is correct and the link still reads 100Mbps, "the issue is almost always an issue with an Ethernet cable". Its advice:

  • Unplug each Ethernet cable and plug it back in. It should click into place firmly. If it doesn't, Intel says to treat the cable as broken.

  • Swap the cable for a known-good one. Intel recommends Cat 6 or better and says a "failed" Cat 5e or Cat 6 cable will often still work at 100Mbps. It also notes that cheap Cat 5e cables can be damaged easily, for example by being run over by an office chair or trapped in a door.

  • Remember every cable in the chain, including the ones between a wall socket and the router.

Our Cat5e vs Cat6 vs Cat8 guide explains which cable to buy.

Step 4: Bypass everything in between

Intel's fastest test is to connect your PC directly to the router with a single known-good Cat 6 cable, preferably into a port you know works at gigabit speed. If the link now shows 1Gbps, the fault is in whatever you bypassed: a switch, powerline adapter, wall socket or another cable.

Other checks Intel suggests:

  • Try a different port on the router or switch.

  • Plug a PC that does get 1Gbps into the suspect cable. If it drops to 100Mbps, the cable or the equipment along it is at fault, not your PC.

  • Power-cycle the router, switch and anything else between your PC and the router.

Step 5: Update the driver, then check the port

If none of that helps, install the latest network driver from your motherboard maker's support page or the chipset maker's site. Intel's article for its Killer adapters suggests a clean reinstall of its software as a first step for slow connections. Our guide to checking your motherboard model shows how to find the right support page.

If the link still won't go above 100Mbps, Intel says the Ethernet port on the motherboard may be faulty. Check the pins in the socket for damage and contact the motherboard or PC maker about warranty. A cheap PCIe or USB network adapter is a stopgap.

Our verdict

An Ethernet link stuck at 100Mbps is almost always a physical problem. Check the link speed in Settings, make sure the adapter is on Auto Negotiation, and then swap in a known-good Cat 6 cable plugged straight into the router. That fixes most cases. If it doesn't, work through the ports, switches and wall sockets in between before suspecting the motherboard. For lag and dropouts that aren't caused by link speed, see our guide to fixing high ping and packet loss.

The bottom line

An Ethernet link stuck at 100Mbps is almost always a physical problem. Check the link speed in Settings, make sure the adapter is on Auto Negotiation, and then swap in a known-good Cat 6 cable plugged straight into the router. That fixes most cases. If it doesn't, work through the ports, switches and wall sockets in between before suspecting the motherboard. For lag and dropouts that aren't caused by link speed, see our guide to fixing high ping and packet loss.

Sources

  1. 01Intel, Ethernet Link Speed Capped at 100 Mbps
  2. 02Voyager, How to Check the Link Speed of Your Network Connection in Windows 11

About the author

Forge PC Staff

Editorial team

The shared byline for articles researched, written and edited by the Forge PC editorial team. How we source, check and correct our work is set out in our editorial policy.

More from Forge PC Staff

Read next

How to Enable Wake-on-LAN in Windows 11 (and Why It Stops Working)

How-To

How to Enable Wake-on-LAN in Windows 11 (and Why It Stops Working)

To use Wake-on-LAN, connect the PC by Ethernet, enable wake in the BIOS, turn on Wake on Magic Packet and 'Allow this device to wake the computer' in Device Manager, and wake the PC from sleep. Microsoft says Windows doesn't arm the network adapter after a Fast Startup shutdown, so use sleep or turn Fast Startup off.

Forge PC Staff4 min

Windows 11 Update Stuck or Failing? 9 Fixes to Try

How-To

Windows 11 Update Stuck or Failing? 9 Fixes to Try

If Windows Update is stuck or failing, back up your files and run the Windows Update troubleshooter in the Get Help app. Then check power and internet, use an admin account, unplug extra hardware, clear the update cache, fix the date and time, update drivers and free at least 20GB of space before trying again and restarting.

Forge PC Staff3 min

How to Use Speculative Decoding in LM Studio to Speed Up Local LLMs

How-To

How to Use Speculative Decoding in LM Studio to Speed Up Local LLMs

Speculative decoding in LM Studio pairs your main model with a much smaller draft model from the same family to speed up generation without changing output quality. Turn on Developer Mode, load the main model and pick a draft model in the chat sidebar. LM Studio says speed-ups vary by prompt and can vanish if the draft model is too big.

Forge PC Staff3 min

Best 2.5GbE Network Switch 2026: Simple Multi-Gig Upgrades for Your Home

Best Picks

Best 2.5GbE Network Switch 2026: Simple Multi-Gig Upgrades for Your Home

TP-Link's TL-SG105-M2 is our pick for most homes: five 2.5GbE ports, 25Gbps switching capacity and a fanless metal case with no setup. The eight-port TL-SG108-M2 (40Gbps) suits bigger setups, and NETGEAR's fanless MS305 is an alternative five-port option. Check that your PC, NAS and router have 2.5GbE ports first.

Forge PC Staff3 min