Wake-on-LAN (WoL) lets another device on your network wake your PC by sending it a special network message, often called a "magic packet". It's useful if you stream games from your desktop to another room, use remote desktop, or run a local AI server that you don't want running all day. Getting it working means lining up settings in the BIOS, the network adapter driver and Windows. This guide is based on Microsoft's and Intel's support documentation. Forge PC hasn't tested every motherboard and network adapter, and menu names vary between manufacturers.
Before you start: wired, same network
Intel's guidance says the waking device and the PC need to be on the same subnet, and WoL may not work if anything other than a single router separates them. In practice, that means the PC should be connected by Ethernet to your home router or a switch on the same network. If your link is unreliable, fix that first with our Ethernet stuck at 100Mbps guide.
You'll also need the PC's MAC address, since most WoL apps ask for it. Open Command Prompt and type ipconfig /all, which Microsoft says displays the full TCP/IP configuration for every adapter; note the "Physical Address" listed under your Ethernet adapter.
Step 1: Enable wake in the BIOS
Intel notes that some motherboards need extra BIOS settings before WoL will work. Restart, enter your BIOS or UEFI setup, and look in the power or advanced menus for an option such as Wake on LAN, Power On by PCI-E or Resume by PCI-E device, and enable it. If you can't find it, check your motherboard manual or ask the manufacturer.
Step 2: Set up the network adapter in Device Manager
Right-click Start, open Device Manager, expand Network adapters, then double-click your Ethernet adapter.
On the Advanced tab, Intel recommends setting the following for its adapters (other brands use similar names):
Shutdown Wake Up: Enabled
Wake on Magic Packet: Enabled
Wake on Pattern Match: Enabled (Intel says WoL may work with this disabled, depending on your setup)
SWOI: optional. It lets specific apps wake the PC from the internet, which Intel says isn't needed for normal WoL.
On the Power Management tab, tick Allow the computer to turn off this device to save power and Allow this device to wake the computer. Only tick Only allow a magic packet to wake the computer if the PC keeps waking up when you don't want it to.
Intel notes that these Power Management options may be greyed out on PCs that use Modern Standby, which has its own set of wake sources.
Step 3: Understand Fast Startup
This is the step most people miss. Microsoft's support article explains that Windows' default shutdown is a "hybrid shutdown", also called Fast Startup. After a hybrid shutdown, Windows deliberately doesn't arm the network adapter for wake. Microsoft's article says WoL is supported from sleep, or from hibernate when you choose it explicitly. Some motherboards can still wake from shutdown because the firmware arms the adapter without Windows' involvement.
So you have two options:
Put the PC to sleep instead of shutting it down. This is the supported route.
Turn off Fast Startup if you need to wake from a full shutdown and your board supports it: Control Panel > Power Options > Choose what the power buttons do > untick Turn on fast startup (recommended) > Save changes. Microsoft doesn't recommend disabling it, and startup will take a little longer.
Microsoft's article was written for Windows 10. Windows 11 uses the same Fast Startup option in Control Panel.
Step 4: Send a magic packet
Use a WoL tool on another device on the same network. Many routers include one in their admin pages, and there are WoL apps for phones and PCs. Enter the MAC address you noted earlier and send the packet. If you use the PC for game streaming, our Sunshine and Moonlight guide covers the streaming side, and our best free remote desktop software list covers remote access.
If it still doesn't work
Intel says firewall, antivirus, BIOS, driver, operating system and router settings all need to be correct. Recheck each one.
Test from sleep first. If that works but waking from shutdown doesn't, Fast Startup or the BIOS is the cause.
Update the network adapter driver from your motherboard or adapter maker's website.
Make sure both devices are on the same local network, not a guest Wi-Fi network.
Our verdict
To use Wake-on-LAN in Windows 11, connect the PC by Ethernet, enable the wake option in the BIOS, turn on Wake on Magic Packet and "Allow this device to wake the computer" in Device Manager, and then wake the PC from sleep. Microsoft says Windows doesn't arm the network adapter after a normal Fast Startup shutdown, so either use sleep or turn off Fast Startup if your board supports waking from shutdown.