Skip to content

VersusGPU

Intel Arc B580 vs RTX 3060 12GB for Local AI: Which Budget 12GB Card?

Intel's Arc B580 and NVIDIA's RTX 3060 12GB both have 12GB of GDDR6 for local AI. The RTX 3060 uses CUDA, which Ollama, llama.cpp and ComfyUI support directly; the newer B580, rated at 456GB/s, runs through Vulkan, SYCL or PyTorch xpu. Beware the 8GB RTX 3060.

By , Editorial team

3 min read

Intel Arc B580 vs RTX 3060 12GB for Local AI: Which Budget 12GB Card?
Intel Arc B580 Limited Edition 12GB compared with ASUS RTX 3060 12GB Dual Gaming OC V2
Intel Arc B580 Limited Edition 12GBASUS RTX 3060 12GB Dual Gaming OC V2
GPU Chip ManufacturerIntelNVIDIA
GPU SeriesArc B580RTX 30 Series
ArchitectureXe2 (Battlemage)—
VRAM Capacity (GB)1212
VRAM TypeGDDR6GDDR6
Base Clock—1320 MHz
Boost Clock—1777 MHz
CUDA / Stream Processor Count—3584
Ray Tracing SupportYesYes
AI / Tensor SupportYesYes
PCIe Interface Version—PCIe 4.0 x16
Typical Board Power (W)190170
Recommended PSU Wattage (W)—550
Minimum PSU Wattage (W)600500

If you want 12GB of video memory for local AI on a budget, two cards to consider are Intel's Arc B580 and NVIDIA's older GeForce RTX 3060 12GB. Forge PC hasn't benchmarked either card, so there are no tokens-per-second or image-generation figures here. This comparison uses Intel's and NVIDIA's specification pages and the documentation for Ollama, llama.cpp and ComfyUI.

Specs side by side

Spec

Intel Arc B580

NVIDIA GeForce RTX 3060

Architecture

Battlemage (Intel lists Q4 2024 launch), TSMC N5

Ampere

Memory

12GB GDDR6

12GB GDDR6 (an 8GB version also exists)

Memory bus

192-bit

192-bit (128-bit on the 8GB version)

Memory bandwidth

456GB/s (19Gbps)

Not listed on NVIDIA's page

AI hardware

160 XMX engines, 233 peak INT8 TOPS

3rd-gen Tensor Cores, 3,584 CUDA cores

Board power

190W TBP

170W graphics card power

Recommended PSU

600W

550W

Interface

PCIe 4.0 x8

PCIe 4.0

Memory: same capacity, different bandwidth

Both have 12GB, so they'll fit models of a similar size. Our LLM quantisation guide explains how model size and quantisation decide what fits. Intel rates the B580's memory bandwidth at 456GB/s. NVIDIA's RTX 3060 page lists the memory size and 192-bit bus but not a bandwidth figure, so we can't put the two side by side from official pages alone.

Watch out for the 8GB RTX 3060. NVIDIA's page lists both 12GB and 8GB configurations, and the 8GB card has a narrower 128-bit bus. For local AI, make sure the listing says 12GB.

Software support

This is where the two differ most.

  • Ollama: Ollama's GPU documentation lists the RTX 3060 among supported NVIDIA cards (compute capability 8.6). Ollama provides additional GPU support through Vulkan, which it says is enabled by default when the back end is installed, and its Vulkan section links Intel's Linux GPU driver instructions; on Windows, most vendors' drivers include Vulkan support without extra steps.

  • llama.cpp: its SYCL back end documentation lists the Arc B580 as a supported Intel Arc B-series card. It also documents a workaround for B-series cards, where the driver can accept allocations larger than VRAM and move the overflow to system RAM, which can exhaust host memory when a model doesn't fit.

  • ComfyUI: NVIDIA cards use CUDA builds of PyTorch; for Intel Arc, ComfyUI's install guide uses PyTorch with xpu support. ComfyUI also offers a separate Intel portable build for Windows.

In short, the RTX 3060 uses CUDA, which all three tools support directly, while the Arc B580 is supported but takes a different back end in each app. Our guide to running local AI on an Intel Arc GPU walks through the setup.

Power and fitting

The B580 has a 190W board power rating and Intel recommends a 600W PSU with one 8-pin connector for its reference card; NVIDIA lists 170W and a 550W system for the RTX 3060. Partner cards vary, so check the specific model.

Which should you buy?

Choose the Intel Arc B580 if you want a newer card with Intel's rated 456GB/s of bandwidth and you're happy to set up Vulkan or SYCL back ends. It's also the newer gaming card; see Arc B580 vs RTX 5060.

Choose the RTX 3060 12GB if you want the CUDA route with the least setup in Ollama, llama.cpp and ComfyUI, or you're buying second-hand. Our used GPU for local AI guide covers what to check, and see our report on the RTX 50 shortage and the RTX 3060 in the UK.

For more options, see our best GPU for local LLMs.

Our verdict

Both give you 12GB for local AI. The RTX 3060 12GB is the lower-effort choice because Ollama, llama.cpp and ComfyUI all support CUDA directly; the Arc B580 is the newer card with 456GB/s of rated bandwidth, but you'll use Vulkan, SYCL or PyTorch xpu instead. Whichever you choose, check it really is a 12GB card.

The bottom line

Both give you 12GB for local AI. The RTX 3060 12GB is the lower-effort choice because Ollama, llama.cpp and ComfyUI all support CUDA directly; the Arc B580 is the newer card with 456GB/s of rated bandwidth, but you'll use Vulkan, SYCL or PyTorch xpu instead. Whichever you choose, check it really is a 12GB card.

Sources

  1. 01Intel, Intel Arc B580 Graphics product specifications
  2. 02NVIDIA, GeForce RTX 3060 family specifications
  3. 03Ollama on GitHub, Hardware support (docs/gpu.mdx)
  4. 04llama.cpp on GitHub, SYCL back end documentation
  5. 05ComfyUI on GitHub, Installation guide (docs/installation.md)

About the author

Forge PC Staff

Editorial team

The shared byline for articles researched, written and edited by the Forge PC editorial team. How we source, check and correct our work is set out in our editorial policy.

More from Forge PC Staff

Read next

How to Work Out What Running Local AI Costs in Electricity (UK, 2026)

How-To

How to Work Out What Running Local AI Costs in Electricity (UK, 2026)

Multiply watts by hours, divide by 1,000 and multiply by your unit rate. At Ofgem's average cap rate of 26.32p per kWh (1 October to 31 December 2026), an RTX 5090 at its full 575W rating costs about 15p an hour. Measure your own PC with nvidia-smi or a plug-in energy monitor.

Forge PC Staff4 min

How to Run MiniMax H3 Image Locally in ComfyUI

How-To

How to Run MiniMax H3 Image Locally in ComfyUI

ComfyUI natively supports MiniMax H3 Image, an open-weights model for text-to-image and reference-image editing in six fixed steps at up to 4096x4096. Update ComfyUI, download the diffusion model, VAE and Qwen3-VL text encoder, load the template, and connect images and the VAE to edit.

Forge PC Staff3 min

How to Speed Up LLM Text Generation in ComfyUI With MTP

How-To

How to Speed Up LLM Text Generation in ComfyUI With MTP

ComfyUI v0.45.0 rebuilt local LLM text generation for Qwen3.x models with multi-token prediction and adaptive tree drafting, which Comfy says can roughly double token rates on the same GPU. Update ComfyUI, leave mtp on auto in the Text Generate node and measure your own gains.

Forge PC Staff3 min